Robe Hook Projection: Freeze Door-Swing and Traffic Clearance Before the Listing

A hook that holds a wet robe is not a clearance result. Robe hook projection should be frozen against a named door swing or a named traffic path, with a datum from the finished wall or backplate to the outermost tip, before the listing is approved. Do not treat wet-load, retention, or hook-to-hook spacing files as a substitute for that path check.

This guide is for importers and private-label teams specifying wall-mounted robe hooks for bathrooms and similar rooms where a door, casing, or walkway sits close to the hook. It does not invent a universal millimeter, and it does not close wet-load, retention, or spacing questions. Koitor Hardware, a family-owned China OEM manufacturer of bathroom and home-storage metal hardware, can review a projection brief with a drawing or a sample; the buyer still has to name the path, the datum, and the words that may appear on the artwork.

Why wet-load, retention, and spacing do not clear the path

Wet-load work, when it exists, asks whether a hook keeps a named wet textile without opening or taking a set. Retention work asks whether a loop or belt stays on the hook under ordinary lift-off. Spacing work asks how far one hook stands from another, or from a corner, so two garments can hang. None of those files answers whether the tip enters a door swing or a shoulder line in a hall.

A shopper can hang a robe successfully and still strike the hook with a door, a towel, or a hip. After-sales then sounds like the hook sticks out too far, even when load and spacing were accepted. That complaint belongs to a projection-versus-path file, not to a quietly rewritten load page.

Door hardware, stops, and casing thickness change the remaining clearance even when the hook drawing is unchanged. A hook that clears a flat wall and a thin casing may not clear a thick casing, a bumper, or an inward-swing door that parks close to the hook wall. Write those room facts into the path, or keep the listing silent on room fit.

Preparing drawings and samples for a custom hardware factory is a useful neighbor when the hook outline, the tip, and the backplate must be visible on paper. It does not, by itself, freeze a door swing. Attach the path and the datum to the drawing pack; do not assume a sample photo taken on a bare board is a room clearance pass.

Worked example: first-article photos show two robes hanging and a tip-to-tip spacing that matches the drawing. A week later, a hotel-style complaint is not the issue here; a home importer reports that the bedroom door hits the hook when it opens fully. The spacing file was not wrong. The swing was never named.

Worked example: artwork says slim profile or compact hook with no path, no datum, and no door handing. Those words will be read as a clearance promise. Either bound them with a named path, or remove them.

How should the door swing or traffic path be named?

Name the moving object and the parked position. For a door, say whether it swings toward the hook wall or away from it, whether it is hinged on the hook side or the far side, and whether the check is at a fully open stop, at a 90 degree park, or at both. For a hall or toilet-room walkway, say whose shoulder or garment is being cleared: a person passing, a person turning, or a hanging robe being passed.

Name the fixed neighbors that eat clearance: casing thickness, a door stop, a towel ring on the same wall, a light switch plate, or a trim return. A hook that is acceptable on a flat painted wall can still be struck because the casing sits proud and the door lands closer to the tip than the drawing suggested.

Do not use a generic small bathroom as the path. Two rooms with the same floor area can differ because one door parks against the hook wall and the other parks on the opposite jamb. If the buyer cannot name a path, the honest listing stays silent on room fit and shows only the hook itself.

Worked example: the brief says an inward-swing bathroom door, hinged on the left as viewed from inside, parks at a wall stop 40 mm off a tiled hook wall, and the hook center is specified a stated distance from the casing. The check is whether any part of the hook, including a double prong, meets the door face or a thick robe on the hook at that park. That sentence can be repeated. Fits most doors cannot.

Traffic paths need the same care. A hook beside a narrow passage can clear a closed door and still catch a shoulder. Write the passage width only as a project fact the buyer supplies, and do not invent a Koitor corridor rating. If the path is a passing shoulder rather than a door, say so, and photograph the hook on the wall used for that check, not only on a table.

Pocket doors, sliding barn doors, and out-swing doors are different paths. A sliding panel that travels in front of the hook wall can strike a tip that a swinging door would miss. If the program may sell into rooms with sliding doors, either include that path or exclude it in the listing notes.

Double hooks and robe-and-hat trees change the outermost point. Measure to the tip that actually stands farthest from the wall, which may be the lower prong, an upturned end, or a decorative ball. A single-hook photo used to defend a double-hook SKU is not a path check.

How should projection be measured, and what is out of scope?

Write the datum. Projection in this file is the distance from a named back-reference, usually the finished wall or the back face of the backplate, to the outermost point of the hook. Say whether a decorative cap, a set-screw boss, or a double prong is included. A length taken along the curved wire is not the same as a stand-off from the wall.

Record the sample attitude. A hook lying on a table can be measured, and that measurement is useful, but the path check happens on a wall, a door leaf, or a casing mock-up that matches the named path. Keep both in the pack when both are used, and do not let the table measurement stand in for the swing photograph.

This article does not invent a universal millimeter. The project may write a maximum stand-off, a minimum remaining gap to a named door face, or only a qualitative rule such as no contact with the door at the parked position, including a hanging robe if the listing shows one. Write the rule you will actually use.

Wet-load, retention, and hook-to-hook spacing stay out of the core measurement. You may note them as exclusions so a reviewer does not try to close them here. A hook can be short enough for a door and still fail a wet-load file, and the reverse is also true.

Worked example: the drawing lists a projection from the backplate to the tip. The first-article sample matches that number on the table. The door mock-up, built to the named casing and stop, still kisses the lower prong of a double hook. The table number was not wrong. The path check failed, and the double-hook tip had not been named as the outermost point on paper.

Worked example: a team wants to reuse a towel-bar projection method. A bar is a different shape, and it is usually farther from the jamb. Custom bathroom towel rack manufacturing can be a place to discuss rail stand-off as a different product family. Do not copy a towel-bar clearance photo onto a robe hook and call the path closed.

Finish thickness and backplate gaskets can add a small stand-off after coating. If the project will compare a drawing in bare metal to a finished sample, say whether the coated and gasketed state is the one that must meet the path rule. Do not hide that difference inside a finish-only conversation.

What must stay off the listing until the path is cleared?

Do not print fits any door, slim enough for tight spaces, or compact for small bathrooms unless the named path was checked and the words are bounded to that path. Those phrases will be read as clearance promises. If the path is not named, stay silent on room fit.

Lifestyle photos that show a hook immediately beside an open door are evidence, not decoration. If the photo is staged with the door only slightly open, or with the hook placed farther from the jamb than the installation diagram, either correct the photo or keep the door out of the frame. A shopper will treat the photo as a fit claim.

Robe hook projection language, if it appears at all, should stay inside the method: stand-off from a named datum, checked against a named swing or walkway, with or without a hanging garment as the brief requires. If you cannot write those conditions, do not use projection as a marketing adjective.

Worked example: a retailer wants no more door collisions in the title. There is no named handing, no stop, and no robe in the check. The honest options are to write a path method, to drop the collision language, or to run a project mock-up whose result is owned by the buyer, not invented here as a universal clearance.

Worked example: a collection includes a single hook and a double hook under one compact line name. The double hook stands farther from the wall. Inheriting the single-hook path result is not conservative enough. Repeat the check on the double hook, and split the listing language if the results differ.

Installation diagrams that place a hook a stated distance from a casing are part of the path, not a spacing-between-hooks file. If the diagram is tighter than the mock-up you used, the listing and the diagram disagree. Align them before artwork is approved.

What should the importer freeze before artwork is approved?

This list is specific to projection versus a named door swing or traffic path. It is not a wet-load list, not a retention list, and not a hook-to-hook spacing list.

• The hook family: single, double, or another outline, and which tip is the outermost point.
• The datum: finished wall or backplate, and whether coating and gaskets are included.
• The named door swing or traffic path, including handing, park position, and fixed neighbors such as casing and stops.
• Whether a hanging robe or other textile is part of the check, if the listing will show one.
• The project rule: no contact, a remaining gap the buyer names, or a maximum stand-off the buyer names, with no universal millimeter invented here.
• An explicit exclusion of wet-load, retention, and hook-to-hook spacing from this file.
• How table measurements and wall or mock-up photographs are kept together in the first-article pack.
• How later lot observation will be sampled, written separately from the path method.

If those lines are missing, a robe hook projection complaint will have no path rule to stand on. A request that only says the hook must not stick out too far is not yet a projection file.

First-article records should keep the table stand-off, the wall or mock-up photograph at the parked path, and the outline drawing that names the outermost tip. A single pretty hook shot on a bare tile does not replace that set. If the door in the photograph is not the door in the brief, label the photo as styling and do not use it as a pass.

If a program will sell several hook outlines under one collection name, do not inherit a path result from the shortest hook. Repeat the method on the revision that stands farthest from the wall, and give the SKUs different item numbers if their path results are not the same.

After-sales comments that the door hits the hook, or that people catch a hip in a narrow passage, are the reason this file exists. Classify those comments as path-and-projection until a wet-load or spacing issue has also been checked, and do not close the complaint on holding performance alone.

A hook mounted on a tile return, a half-wall, or the side of a cabinet is still a projection problem if a door or a walkway can meet the tip. Name that mounting wall in the path. Do not assume a center-of-wall bathroom photo covers a hook placed on a narrow pilaster next to the jamb.

Sliding or bifold doors, as noted earlier, need their own park and travel. If the buyer later adds a sliding-door room set to the program, reopen the file. A swing-door pass does not travel with the collection automatically.

Retail copywriters sometimes turn silence on millimeters into low profile or space saving. Those words are still clearance claims if a shopper can reasonably read them as a path promise. If the brief has no path and no result, keep those adjectives off the projection sentence. Use outline facts you can show, such as a named stand-off on the drawing, without converting that number into a room-fit slogan.

How can a family-owned OEM review the projection brief?

Koitor Hardware can review a drawing or a sample together with the datum, the named path, and the intended listing phrase. The useful conversation is outline and acceptance: whether the hook can be made as drawn, and whether the words on the listing are broader than the brief. That is not a promise of a universal clearance or a standard projection for every room.

Small-batch customization is often where a hook is lengthened for a thicker robe or given a decorative ball without a new path check. If the outermost point changes, repeat the method on the new revision. Do not carry a previous collection photo forward as proof.

MOQ can start from about 100 pcs depending on the product. Samples usually take 5–7 working days after details are confirmed. Bulk production usually takes 4–6 weeks depending on the project, finish, quantity, and packaging. Those figures are planning ranges and do not, by themselves, include a door-swing study unless the brief asks for one.

When you send the projection brief and a sample to Koitor, include the datum, the path, and the listing phrase or an explicit decision to stay silent on room fit. Koitor can then discuss تصنيع تجهيزات الحمامات حسب الطلب as a construction and acceptance review, not as a source of a pack clearance rating.

الأسئلة الشائعة

Can a wet-load pass be used to say robe hook projection is acceptable in a tight room?

No. Wet-load is about holding a named textile. Projection versus a door or a walkway is a different interface. Run both when both can fail, and do not let a holding result stand in for a path result.

Does this page set hook-to-hook spacing?

No. Spacing between hooks, or from a hook to a corner for two garments, stays in a spacing file. This page may mention spacing only as an exclusion so the two decisions are not mixed.

Where should projection be measured?

From the datum you froze, usually the finished wall or the back of the backplate, to the outermost tip. Confirm the same number, or the same qualitative rule, on the named path, not only on a table.

Should a hanging robe be part of the check?

Include it when the listing shows a robe or when the buyer cares about a dressed hook at a parked door. If the check is bare and the artwork is dressed, the file and the listing disagree.

Can Koitor publish a standard projection that fits every bathroom door?

No universal Koitor clearance or room-fit rating is stated here. Koitor can review the outline and the path you specify, and can discuss a project method. The buyer still owns the listing words.

What if the door hardware or casing changes after first article?

Reopen the path file. A hook that cleared one casing and stop may not clear a thicker trim or a different bumper, even if the hook SKU is unchanged.

اعمل مع شركة «كويتور» للأدوات