{"id":8443,"date":"2026-11-16T00:36:52","date_gmt":"2026-11-16T00:36:52","guid":{"rendered":"https:\/\/koitorhardware.com\/?p=8443"},"modified":"2026-11-16T00:36:52","modified_gmt":"2026-11-16T00:36:52","slug":"replacement-hinge-each-leaf-corner-outline","status":"publish","type":"post","link":"https:\/\/koitorhardware.com\/de\/replacement-hinge-each-leaf-corner-outline\/","title":{"rendered":"Hinge Radius: Record Each Replacement Leaf\u2019s Corner Shape Before Ordering"},"content":{"rendered":"<p>When a replacement hinge is being identified, record the outer corner outline of each leaf separately. One leaf may be square while its mating leaf is rounded, so a single \u201chinge radius\u201d field can leave the order ambiguous. Tie each outline to the correct moving or fixed member, drawing view, supplier model, and evidence source. Then ask the hinge supplier to confirm the proposed replacement and any remaining compatibility questions.<\/p>\n<p>This is a component-identification and RFQ guide. It does not explain how to remove a hinge, modify a door or enclosure, route a recess, select a structural hinge, or approve a replacement for a specific application. A matching corner outline is only one attribute. It does not establish hinge size, handing, pin configuration, hole pattern, clearance, load capacity, or compatibility with the complete assembly.<\/p>\n<h2>What does \u201chinge radius\u201d mean in a replacement order?<\/h2>\n<p>In buyer conversations, \u201chinge radius\u201d often refers to a rounded outer corner on a hinge leaf. That phrase needs clarification because a hinge includes multiple parts and dimensions, and suppliers may use different terminology. Ask whether the term means the corner outline of a leaf, another radius on the hinge geometry, or a different product dimension.<\/p>\n<p>For a replacement order, the most useful record names both mating leaves and gives each its own corner description. The fixed-member leaf and moving-member leaf should have separate fields. If both appear identical, state that they are believed to match and ask the supplier to confirm from its product record. Do not leave one shared field to imply that two different parts necessarily have the same outline.<\/p>\n<p>A manufacturer\u2019s replacement guide, <a href=\"https:\/\/watersonusa.com\/solutions\/1-4-vs-5-8-radius-hinge\" rel=\"nofollow noopener\" target=\"_blank\">Waterson\u2019s comparison of hinge corner configurations<\/a>, advises checking both leaves and describes a configuration where the leaves have different corners. Deltana\u2019s <a href=\"https:\/\/deltana.net\/media\/marketing\/products\/3\/265\/Deltana_Catalog_22.0.pdf\" rel=\"nofollow noopener\" target=\"_blank\">manufacturer catalogue<\/a> also shows a named radius\/square configuration. These examples establish that unlike outlines can occur in a particular product family. They do not mean every hinge uses mixed corners, that any such parts are interchangeable, or that the example will fit a buyer\u2019s enclosure.<\/p>\n<p>The practical action is to turn an informal observation into a traceable identification field. \u201cOne round, one square\u201d is a useful starting note, but an order record should connect those descriptions to the specific leaf, hinge model, mating member, and source drawing. If the buyer cannot identify a leaf confidently, mark it unresolved rather than guessing.<\/p>\n<h2>Why should the two hinge leaves be recorded independently?<\/h2>\n<p>The two leaves mate with different parts of the assembly and may have different outlines. A single corner descriptor can incorrectly imply symmetry. A replacement request should make the distinction visible before quotation, cross-reference, or sample approval.<\/p>\n<p>Record leaf identity by function and orientation. For example, identify the leaf attached to the moving panel and the leaf attached to the fixed frame, using the project\u2019s actual terminology. Add a consistent drawing view so the supplier can understand which edge and corner are being described. Do not assume \u201cleft\u201d and \u201cright\u201d are self-explanatory; those labels can depend on viewing direction, door opening, or the drawing convention.<\/p>\n<p>A useful outline record includes:<\/p>\n<div class=\"wp-block-table koitor-responsive-table\" style=\"max-width:100%;overflow-x:auto;\">\n<table style=\"width:100%;border-collapse:collapse;overflow-wrap:anywhere;\">\n<thead>\n<tr>\n<th>Record field<\/th>\n<th>Moving-member leaf<\/th>\n<th>Fixed-member leaf<\/th>\n<\/tr>\n<\/thead>\n<tbody>\n<tr>\n<td>Component identity<\/td>\n<td>Drawing label or exact part code<\/td>\n<td>Drawing label or exact part code<\/td>\n<\/tr>\n<tr>\n<td>Mating member<\/td>\n<td>Named moving panel or door<\/td>\n<td>Named frame or fixed structure<\/td>\n<\/tr>\n<tr>\n<td>Outer corner<\/td>\n<td>Square, rounded, or documented special outline<\/td>\n<td>Record independently; do not copy by assumption<\/td>\n<\/tr>\n<tr>\n<td>Evidence<\/td>\n<td>Maker drawing, product model, or controlled image<\/td>\n<td>Maker drawing, product model, or controlled image<\/td>\n<\/tr>\n<tr>\n<td>Status<\/td>\n<td>Confirmed, proposed, or unresolved<\/td>\n<td>Confirmed, proposed, or unresolved<\/td>\n<\/tr>\n<tr>\n<td>Other interfaces<\/td>\n<td>Holes, thickness, pin and other features tracked separately<\/td>\n<td>Holes, thickness, pin and other features tracked separately<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<\/div>\n<p>This table is a purchasing aid, not a universal hinge drawing standard. Use the project\u2019s controlled labels and units. If the supplier\u2019s drawing uses different terms, preserve its wording and add a buyer-side explanation instead of silently rewriting the specification.<\/p>\n<p>The separate fields also make comparison more accurate. One supplier may quote a product whose leaves have matching outlines; another may quote a named mixed-corner option. If the RFQ contains only one radius value, the offers may appear equivalent even though the leaf configurations differ. Keeping two fields allows purchasing to ask a precise question: does the quoted model reproduce the documented outline on each corresponding leaf?<\/p>\n<p>Separate identification is useful even when both corners ultimately match. It shows that the team considered both interfaces and received confirmation, rather than assuming that a single observation described the whole hinge. A blank field can remain visible until the supplier answers.<\/p>\n<h2>How should a buyer describe each corner outline?<\/h2>\n<p>Use a clear, repeatable reference view and identify the actual outer corner being described. If the supplier has a dimensioned product drawing, use its model and terminology. If the buyer is working from an existing part, provide a controlled photograph or drawing reference that distinguishes the two leaves. Do not infer a precise radius from a perspective photograph or use an unverified measurement as a manufacturing tolerance.<\/p>\n<p>A replacement-part guide from Stone Harbor Hardware, <a href=\"https:\/\/www.stoneharborhardware.com\/blogs\/articles\/hardware-basics-how-to-determine-the-radius-of-a-hinge\" rel=\"nofollow noopener\" target=\"_blank\">\u201cHow to Determine the Radius of a Hinge\u201d<\/a>, distinguishes square and rounded corners in its discussion. The source\u2019s measurement illustration was not available in the research review, so this article does not reproduce a measurement method or recommend a tool-based test. Its general distinction can help name the buyer question; the actual replacement specification should come from the selected manufacturer\u2019s evidence.<\/p>\n<p>For a visual record, keep the hinge flat and show the complete leaf outline in a consistent orientation. Label which mating member each leaf belongs to. If a photograph is used, include a scale reference only if the source and measurement method are controlled; otherwise treat the photograph as identification evidence, not dimensional evidence. A picture can show that a leaf appears square or rounded, but it cannot establish a precise radius, tolerance, hole position, material, or product identity.<\/p>\n<p>When a model drawing already specifies the corner option, cite the model number and drawing revision. If the catalog uses a product code rather than a verbal description, quote the code exactly. Do not substitute \u201cstandard radius\u201d or \u201cregular corner\u201d unless the supplier defines what that means for its product family.<\/p>\n<p>Distinguish the outer leaf-corner outline from other hinge geometry. A hinge has a barrel or knuckle, pin, leaf thickness, open width, overall length, mounting holes, and movement through its operating range. A radius used for a leaf corner is not automatically a barrel bend radius, the clearance around the hinge, an opening angle, or a dimension that describes the door\u2019s cutout. These fields may all matter to a replacement decision, but they answer different questions.<\/p>\n<h2>Does a matching corner shape prove the replacement hinge will fit?<\/h2>\n<p>No. A matching corner outline establishes only that one visible feature appears aligned with the reference. The supplier and responsible product reviewer still need to confirm the exact hinge model and all other interfaces. Do not accept or reject a replacement solely because its corners look similar.<\/p>\n<p>A buyer can keep a compatibility checklist beside the corner record:<\/p>\n<ul>\n<li>The exact original product or component identity is known, or uncertainty is marked.<\/li>\n<li>Both leaves are shown and individually labeled.<\/li>\n<li>The drawing view and orientation are stated.<\/li>\n<li>Each corner outline is recorded separately.<\/li>\n<li>Hinge overall dimensions and open width are checked against controlled evidence.<\/li>\n<li>Hole pattern and other mounting interfaces are recorded separately.<\/li>\n<li>Pin, handing, movement, and any special feature are referred to the supplier.<\/li>\n<li>The quoted model and source revision are identified.<\/li>\n<li>The supplier confirms which attributes match and which remain unresolved.<\/li>\n<li>Any application-specific structural or safety review remains with the responsible qualified party.<\/li>\n<\/ul>\n<p>The list is not an installation guide or an acceptance standard. It prevents a limited visual match from being mistaken for full product equivalence. If a buyer needs a fit decision for an actual assembly, provide the supplier with the exact controlled drawing or part identity and request a written response that names the model reviewed.<\/p>\n<p>A corner outline does not prove that existing holes align, that the hinge is appropriate for a door or enclosure, that the pin arrangement is correct, or that the product is suitable for the application. Do not infer performance, security, fire rating, accessibility, load rating, or regulatory compliance from a corner profile or catalog image. Those statements require separate evidence and responsible review.<\/p>\n<p>The distinction is important for replacement programs. A part may resemble the original in a photograph yet differ in a mating dimension or function. Conversely, a visible corner difference may be an intentional option for a specific design. The buyer should not make a field modification based on a blog description. Keep the part identification and any alteration or installation question with the hinge manufacturer or qualified project professional.<\/p>\n<h3>How can a supplier comparison avoid false equivalence?<\/h3>\n<p>Compare the quoted hinge models field by field. A buyer\u2019s spreadsheet should not collapse unlike leaf outlines into one generic \u201cradius\u201d value. Preserve the source label from each supplier and use separate buyer fields to note which leaf and feature it describes.<\/p>\n<div class=\"wp-block-table koitor-responsive-table\" style=\"max-width:100%;overflow-x:auto;\">\n<table style=\"width:100%;border-collapse:collapse;overflow-wrap:anywhere;\">\n<thead>\n<tr>\n<th>Comparison item<\/th>\n<th>Supplier A<\/th>\n<th>Supplier B<\/th>\n<th>Buyer decision<\/th>\n<\/tr>\n<\/thead>\n<tbody>\n<tr>\n<td>Manufacturer and model<\/td>\n<td>Exact code and revision<\/td>\n<td>Exact code and revision<\/td>\n<td>Confirm product identity<\/td>\n<\/tr>\n<tr>\n<td>Moving-member leaf outline<\/td>\n<td>Supplier term and drawing reference<\/td>\n<td>Supplier term and drawing reference<\/td>\n<td>Same, different, or unresolved<\/td>\n<\/tr>\n<tr>\n<td>Fixed-member leaf outline<\/td>\n<td>Supplier term and drawing reference<\/td>\n<td>Supplier term and drawing reference<\/td>\n<td>Same, different, or unresolved<\/td>\n<\/tr>\n<tr>\n<td>View\/orientation<\/td>\n<td>Drawing view and member labels<\/td>\n<td>Drawing view and member labels<\/td>\n<td>Is the comparison aligned?<\/td>\n<\/tr>\n<tr>\n<td>Other dimensions<\/td>\n<td>Listed separately from corner shape<\/td>\n<td>Listed separately from corner shape<\/td>\n<td>Request missing evidence<\/td>\n<\/tr>\n<tr>\n<td>Mounting interface<\/td>\n<td>Hole pattern or mating reference<\/td>\n<td>Hole pattern or mating reference<\/td>\n<td>Have responsible supplier confirm<\/td>\n<\/tr>\n<tr>\n<td>Application scope<\/td>\n<td>Stated product use and limits<\/td>\n<td>Stated product use and limits<\/td>\n<td>Do not infer suitability<\/td>\n<\/tr>\n<tr>\n<td>Evidence source<\/td>\n<td>Catalog, drawing, or written confirmation<\/td>\n<td>Catalog, drawing, or written confirmation<\/td>\n<td>Current and applicable?<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<\/div>\n<p>The row \u201csame, different, or unresolved\u201d is a buyer\u2019s comparison status, not a technical pass\/fail rating. It helps identify where clarification is needed. If one supplier cannot provide a drawing, record that gap rather than treating its verbal description as equal evidence.<\/p>\n<p>A fair comparison also considers whether the products serve the same function. Some hinges are intended for specific furniture, cabinet, enclosure, or architectural applications. The buyer should confirm the product category with the manufacturer and avoid moving an example from one application into another without supporting evidence. This post does not recommend any hinge for a door, cabinet, or metal storage product.<\/p>\n<p>Record whether a supplier is quoting the full hinge assembly or a selected component. The corner description belongs to an identified leaf, but the order may include both leaves, a pin, fasteners, or another item depending on the product. Do not assume the order unit or included parts from a product photograph. Ask the supplier to state precisely what the quote contains.<\/p>\n<p>When one manufacturer offers a mixed-corner product and another does not, a buyer can request a model-specific alternative or mark the comparison as not equivalent. The correct result may be to hold the substitution until the project owner decides whether a different interface is acceptable. A \u201cnot comparable yet\u201d status protects the decision process from a premature price comparison.<\/p>\n<h2>What information belongs in a replacement hinge RFQ?<\/h2>\n<p>The RFQ should help the supplier identify the current component and understand what the buyer needs confirmed. Attach a controlled drawing or clear part reference, identify both mating members, and keep the corner outline fields distinct from the other hinge dimensions. If the original product identity is unavailable, say so and provide the available evidence without presenting an estimate as a fact.<\/p>\n<p>Useful RFQ fields include:<\/p>\n<ul>\n<li>Original manufacturer, model, or part code, if known.<\/li>\n<li>Quantity and whether the request is for a complete pair or another defined order unit.<\/li>\n<li>Moving-member leaf identifier and its corner outline.<\/li>\n<li>Fixed-member leaf identifier and its corner outline.<\/li>\n<li>Consistent top, side, or face view and the source drawing revision.<\/li>\n<li>Overall hinge dimensions and open width from controlled evidence, if available.<\/li>\n<li>Hole pattern and other mounting details recorded separately.<\/li>\n<li>Pin or handing question for the supplier to resolve.<\/li>\n<li>Target assembly and intended application, without unsupported performance claims.<\/li>\n<li>Existing sample or photograph, labeled as identification material.<\/li>\n<li>Requested confirmation of the replacement model and its exact scope.<\/li>\n<li>Open questions requiring supplier response before order approval.<\/li>\n<\/ul>\n<p>Do not use an RFQ to prescribe machining, cutting, drilling, door modification, or hinge installation. If the supplier requests those details, provide them through the project\u2019s approved technical process and let the responsible reviewer determine what is necessary. This article is limited to specification and identification.<\/p>\n<p>A concise inquiry can say: \u201cWe are identifying a replacement hinge for the attached assembly. The moving-member leaf appears to have a rounded outer corner and the fixed-member leaf appears square. Please confirm the exact product model, whether this configuration is available, and which drawing or dimensions are needed to verify the other interfaces. The attached photograph is for identification and is not a controlled dimensional drawing.\u201d This wording states what the buyer observed and what remains uncertain.<\/p>\n<p>The supplier response should identify the model quoted, the drawing or catalog source, which leaf description applies, and any required clarification. If the supplier gives only a generic \u201cradius hinge\u201d reply, ask whether the term describes both leaves or just one. Keep the question specific rather than assuming that a shared product label resolved the outline.<\/p>\n<h2>How should samples and existing parts be reviewed?<\/h2>\n<p>Treat a sample as one source of component identity, not proof of complete compatibility. Label each leaf and preserve its orientation before comparing it with the buyer\u2019s drawing. If the sample is worn, damaged, corroded, modified, or missing a part, note that condition rather than treating the sample as an exact representation of the original specification.<\/p>\n<p>At a sample review, record:<\/p>\n<ul>\n<li>Which leaf is associated with each mating member.<\/li>\n<li>The viewpoint used for the outline comparison.<\/li>\n<li>The apparent corner shape of each leaf.<\/li>\n<li>Any markings, model codes, or supplier identifiers.<\/li>\n<li>Which dimensions were taken from a controlled drawing versus observed on the sample.<\/li>\n<li>Which features remain unconfirmed by the manufacturer.<\/li>\n<li>Whether the sample\u2019s condition may affect what can be identified.<\/li>\n<\/ul>\n<p>Do not infer the original manufacturing radius from a used or altered part. Do not decide that two hinges are interchangeable because their leaves appear to align on a tabletop. A tabletop comparison does not assess all interfaces, operation, intended use, or application requirements.<\/p>\n<p>A supplier\u2019s production sample may help verify the quoted model and visible outline against an approved drawing. It still does not replace the supplier\u2019s technical documentation or project approval. The buyer should record which revision the sample represents and whether the supplier confirms it as the production-intent model.<\/p>\n<p>Photographs can be useful in a remote sourcing workflow, but they can distort shape and scale. Take images from a consistent, square-on viewpoint where possible, keep both leaves visible, and label the moving and fixed member. Do not use image similarity as a substitute for a model number or controlled drawing. If an outline cannot be determined confidently, write \u201cunknown\u201d and ask the supplier to identify it.<\/p>\n<h3>What changes should trigger a fresh comparison?<\/h3>\n<p>A change to the hinge model, either leaf, drawing revision, mating member, mounting interface, or intended application should trigger a scoped recheck. A changed corner outline does not automatically make a part unacceptable, but it means the prior record may no longer describe the offered component.<\/p>\n<p>Use change control to identify which field changed, what evidence was updated, who confirmed the new model, and whether other compatibility questions remain open. If only the fixed-member leaf changes, recheck that leaf and confirm whether the moving-member leaf and complete product code remain the same. If a whole model is substituted, do not carry the old corner record forward without supplier confirmation.<\/p>\n<p>The same principle applies to repeat orders. A buyer may reuse an earlier approved record only if the supplier confirms the same product identity and revision or otherwise confirms that the relevant details remain applicable. A new supplier, renamed part, revised catalog, or replacement from another product family should be treated as a new identification question.<\/p>\n<p>Keep the record useful to purchasing and quality teams. Include the order date, quoted model, drawing revision, supplier response, and sample identifier where relevant. If the product information later appears in a replacement-parts catalog or customer service guide, use only the confirmed terms and avoid promising cross-compatibility that the manufacturer did not establish.<\/p>\n<h3>What belongs to Koitor and what remains with the hinge supplier?<\/h3>\n<p>Koitor Hardware\u2019s verified positioning is a family-owned custom metal hardware factory focused on bathroom and home storage hardware, with drawing or sample discussions and flexible OEM production. That supports general metal-storage component and assembly-interface conversations when a particular project is confirmed within scope. It does not establish that Koitor manufactures the residential or architectural hinge shown in an example, modifies doors, supplies a branded replacement hinge, or approves a hinge for structural or regulated use.<\/p>\n<p>For a metal-storage project that includes a bought-in hinge, identify the hinge by supplier and model and show its role in the assembly. Koitor can first confirm whether the surrounding metal component falls within its verified manufacturing scope. The hinge supplier remains responsible for its own model definitions and product documentation; the buyer or qualified project reviewer remains responsible for the application decision.<\/p>\n<p>The <a href=\"https:\/\/koitorhardware.com\/de\/oem-home-storage-hardware-manufacturer\/\">OEM home-storage hardware overview<\/a> provides general company context. It is not evidence that a particular hinge is a Koitor product or that any replacement is approved. For an in-scope metal-storage inquiry, use the <a href=\"https:\/\/koitorhardware.com\/de\/kontakt\/\">Koitor contact page<\/a> and state which parts are custom metal hardware and which are bought-in components.<\/p>\n<p>A helpful project note can identify the component boundary: \u201cThe hinge is a bought-in component under review. The attached outline record separates the moving and fixed leaves. Please confirm whether the related metal enclosure part is within Koitor\u2019s production scope; the hinge manufacturer will confirm the exact model and the remaining hinge interfaces.\u201d This keeps responsibilities visible and avoids implying that a metal-hardware manufacturer has approved a product outside its verified scope.<\/p>\n<h2>Buyer checklist before ordering a replacement hinge<\/h2>\n<p>Before approving an RFQ or replenishment, confirm that the record identifies both mating leaves independently; names the moving and fixed members; records the corner outline for each leaf; uses a consistent drawing view; identifies the source model and revision; distinguishes outline from overall size, hole pattern, pin and handing; labels photographs as identification evidence; asks the supplier to confirm the exact product model; identifies what the quote includes; leaves unknown attributes unresolved; and names the responsible reviewer for application suitability.<\/p>\n<p>This checklist is an administrative aid, not an engineering acceptance standard. It cannot establish that a replacement fits or is suitable for a specific application. A supplier or qualified project reviewer must confirm the relevant product evidence. If any required field is missing, keep the status open rather than filling the gap with an assumption.<\/p>\n<figure class=\"wp-block-image size-large koitor-blog-image\" style=\"margin:32px 0;\">\n  <img decoding=\"async\" src=\"https:\/\/koitorhardware.com\/wp-content\/uploads\/2026\/11\/K1637-process-delivery.webp\" alt=\"Buyer recording the corner outline of each replacement hinge leaf from one consistent viewpoint\" style=\"width:100%;max-width:960px;height:auto;display:block;margin:0 auto;border-radius:10px;\"  srcset=\"https:\/\/koitorhardware.com\/wp-content\/uploads\/2026\/11\/K1637-process-delivery-18x10.webp 18w, https:\/\/koitorhardware.com\/wp-content\/uploads\/2026\/11\/K1637-process-delivery-150x150.webp 150w, https:\/\/koitorhardware.com\/wp-content\/uploads\/2026\/11\/K1637-process-delivery-300x169.webp 300w, https:\/\/koitorhardware.com\/wp-content\/uploads\/2026\/11\/K1637-process-delivery-768x432.webp 768w, https:\/\/koitorhardware.com\/wp-content\/uploads\/2026\/11\/K1637-process-delivery-1024x576.webp 1024w, https:\/\/koitorhardware.com\/wp-content\/uploads\/2026\/11\/K1637-process-delivery.webp 1200w\" sizes=\"(max-width: 1200px) 100vw, 1200px\" loading=\"lazy\"\/><figcaption style=\"font-size:14px;color:#667085;text-align:center;margin-top:8px;\">Record the two leaf outlines independently and keep other hinge dimensions separate.<\/figcaption><\/figure>\n<h2>H\u00e4ufig gestellte Fragen<\/h2>\n<h3>Can the two leaves of one hinge have different corner shapes?<\/h3>\n<p>Yes, a manufacturer can offer a named configuration where one leaf is rounded and the other square. Deltana\u2019s catalog and Waterson\u2019s replacement guide provide model-specific examples. Confirm the exact selected model; this is not a universal configuration or an interchangeability rule.<\/p>\n<h3>Does \u201chinge radius\u201d identify both leaves?<\/h3>\n<p>Not necessarily. The phrase may be too broad for a two-leaf order record. State the outline of each leaf separately and ask the supplier to clarify its model terminology.<\/p>\n<h3>Does matching the corner shape prove a replacement will fit?<\/h3>\n<p>No. The corner outline is only one feature. Model, dimensions, mounting interfaces, pin, handing, movement, and application suitability require separate confirmation.<\/p>\n<h3>Is a photograph enough to specify a replacement hinge?<\/h3>\n<p>Usually it is only identification evidence. Perspective and scale can obscure the outline and other dimensions. Provide a manufacturer model or controlled drawing where available and label all remaining unknowns.<\/p>\n<h3>Can this guide tell me how to modify an existing door or frame?<\/h3>\n<p>No. It is limited to buyer-side identification and RFQ clarification. Any alteration or installation question belongs with the hinge manufacturer and qualified project professional.<\/p>\n<figure class=\"wp-block-image size-large koitor-blog-image\" style=\"margin:32px 0;\">\n  <img decoding=\"async\" src=\"https:\/\/koitorhardware.com\/wp-content\/uploads\/2026\/11\/K1637-checklist-delivery.webp\" alt=\"Replacement hinge comparison with separate outline fields for each mating leaf\" style=\"width:100%;max-width:960px;height:auto;display:block;margin:0 auto;border-radius:10px;\"  srcset=\"https:\/\/koitorhardware.com\/wp-content\/uploads\/2026\/11\/K1637-checklist-delivery-18x10.webp 18w, https:\/\/koitorhardware.com\/wp-content\/uploads\/2026\/11\/K1637-checklist-delivery-150x150.webp 150w, https:\/\/koitorhardware.com\/wp-content\/uploads\/2026\/11\/K1637-checklist-delivery-300x169.webp 300w, https:\/\/koitorhardware.com\/wp-content\/uploads\/2026\/11\/K1637-checklist-delivery-768x432.webp 768w, https:\/\/koitorhardware.com\/wp-content\/uploads\/2026\/11\/K1637-checklist-delivery-1024x576.webp 1024w, https:\/\/koitorhardware.com\/wp-content\/uploads\/2026\/11\/K1637-checklist-delivery.webp 1200w\" sizes=\"(max-width: 1200px) 100vw, 1200px\" loading=\"lazy\"\/><figcaption style=\"font-size:14px;color:#667085;text-align:center;margin-top:8px;\">A two-field record prevents one leaf\u2019s outline from being assumed for the other.<\/figcaption><\/figure>\n<h3>Arbeiten Sie mit Koitor Hardware zusammen<\/h3>\n<section class=\"koitor-blog-cta\" style=\"margin-top:36px;padding:28px;border:1px solid #D0D5DD;border-radius:16px;background:#F8FAFC;\">\n<h3 style=\"margin-top:0;margin-bottom:12px;font-size:28px;line-height:1.25;color:#101828;\">Discuss a Metal Storage Component and Its Interfaces<\/h3>\n<p style=\"font-size:16px;line-height:1.7;margin-bottom:20px;color:#344054;\">For an in-scope metal-storage project, send Koitor the lawful drawing or sample for the metal component and identify any bought-in hinge by supplier and model. Include the assembly interface, finish, packaging needs, target market, and expected quantity. The hinge manufacturer remains responsible for its own product definition and application evidence.<\/p>\n<div style=\"display:flex;gap:12px;flex-wrap:wrap;align-items:center;margin-bottom:24px;\">\n    <a href=\"https:\/\/koitorhardware.com\/de\/kontakt\/\" style=\"display:inline-flex;align-items:center;justify-content:center;min-height:48px;padding:0 22px;border-radius:8px;background:#FF5A1F;color:#ffffff;font-weight:700;text-decoration:none;line-height:1;\">Request a Project Discussion<\/a><br \/>\n    <a href=\"https:\/\/koitorhardware.com\/de\/oem-home-storage-hardware-manufacturer\/\" style=\"display:inline-flex;align-items:center;justify-content:center;min-height:48px;padding:0 22px;border-radius:8px;border:1px solid #FF5A1F;color:#FF5A1F;background:#ffffff;font-weight:700;text-decoration:none;line-height:1;\">Explore OEM Home Storage<\/a>\n  <\/div>\n<div class=\"koitor-article-tags\" style=\"margin-top:24px;padding-top:18px;border-top:1px solid #E5E7EB;display:flex;align-items:center;gap:8px;flex-wrap:wrap;\">\n    <span style=\"font-size:14px;font-weight:700;color:#344054;margin-right:4px;\">Stichw\u00f6rter:<\/span><br \/>\n    <span style=\"display:inline-flex;align-items:center;justify-content:center;padding:6px 12px;border-radius:999px;background:#FFF3ED;color:#FF5A1F;font-size:13px;font-weight:600;line-height:1.2;\">Leitfaden f\u00fcr Importeure<\/span><br \/>\n    <span style=\"display:inline-flex;align-items:center;justify-content:center;padding:6px 12px;border-radius:999px;background:#FFF3ED;color:#FF5A1F;font-size:13px;font-weight:600;line-height:1.2;\">Product Development<\/span><br \/>\n    <span style=\"display:inline-flex;align-items:center;justify-content:center;padding:6px 12px;border-radius:999px;background:#FFF3ED;color:#FF5A1F;font-size:13px;font-weight:600;line-height:1.2;\">Metallbeschl\u00e4ge f\u00fcr Aufbewahrungsm\u00f6bel<\/span>\n  <\/div>\n<\/section>","protected":false},"excerpt":{"rendered":"<p>Record hinge radius and each replacement leaf\u2019s corner outline separately, then confirm the exact model and mating interface before approving an order.<\/p>","protected":false},"author":1,"featured_media":8440,"comment_status":"closed","ping_status":"","sticky":false,"template":"","format":"standard","meta":{"footnotes":""},"categories":[145],"tags":[40,48,97],"class_list":["post-8443","post","type-post","status-publish","format-standard","has-post-thumbnail","hentry","category-hardware-sourcing-knowledge","tag-importer-buying-guide","tag-metal-storage-hardware","tag-product-development"],"_links":{"self":[{"href":"https:\/\/koitorhardware.com\/de\/wp-json\/wp\/v2\/posts\/8443","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/koitorhardware.com\/de\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/koitorhardware.com\/de\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/koitorhardware.com\/de\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/koitorhardware.com\/de\/wp-json\/wp\/v2\/comments?post=8443"}],"version-history":[{"count":1,"href":"https:\/\/koitorhardware.com\/de\/wp-json\/wp\/v2\/posts\/8443\/revisions"}],"predecessor-version":[{"id":8456,"href":"https:\/\/koitorhardware.com\/de\/wp-json\/wp\/v2\/posts\/8443\/revisions\/8456"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/koitorhardware.com\/de\/wp-json\/wp\/v2\/media\/8440"}],"wp:attachment":[{"href":"https:\/\/koitorhardware.com\/de\/wp-json\/wp\/v2\/media?parent=8443"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/koitorhardware.com\/de\/wp-json\/wp\/v2\/categories?post=8443"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/koitorhardware.com\/de\/wp-json\/wp\/v2\/tags?post=8443"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}