{"id":8419,"date":"2026-11-16T00:33:57","date_gmt":"2026-11-16T00:33:57","guid":{"rendered":"https:\/\/koitorhardware.com\/?p=8419"},"modified":"2026-11-16T00:33:57","modified_gmt":"2026-11-16T00:33:57","slug":"extended-strike-plate-measurement-datum","status":"publish","type":"post","link":"https:\/\/koitorhardware.com\/es\/extended-strike-plate-measurement-datum\/","title":{"rendered":"Extended Strike Plate Size: Confirm the Measurement Datum Before Comparing Parts"},"content":{"rendered":"<p>An extended strike plate should be compared by its stated measurement reference, not by a catalog label alone. One manufacturer defines the nominal size of its reviewed extended-lip family from the center of the installation screw holes to the end of the lip, while separately describing the plate\u2019s overall length. That convention belongs to that maker\u2019s product range; it is not a universal strike-plate rule. Before an importer compares offers, record the named size, where its measurement starts and ends, the separate overall dimensions, and the drawing or product document that supports each field.<\/p>\n<p>This distinction helps a buyer avoid comparing unlike measurements in a replacement or private-label specification. It does not establish that a part fits a door, latch, frame, or security application. A correctly understood nominal dimension is one input to identification; model-specific drawings and qualified system review remain responsible for fit and performance.<\/p>\n<h2>Why should buyers identify the size datum first?<\/h2>\n<p>A dimension has a meaning only when its reference points are clear. A product label may use a distance measured from a functional reference, while another seller may describe an edge-to-edge envelope. If both values are called \u201csize,\u201d a spreadsheet can make them look comparable even when they measure different spans.<\/p>\n<p>In the reviewed Stone Harbor Hardware example, the maker explains that the nominal size for its extended-lip strike family runs from the centerline of the installation screw holes to the lip end. It separately explains the relationship between that named size and the plate\u2019s overall length for its own products. Buyers can use the example to ask a better question: what exactly does this supplier\u2019s catalog number represent? They should not copy the family\u2019s numeric relationship into another manufacturer\u2019s specification.<\/p>\n<p>The primary source is the manufacturer\u2019s <a href=\"https:\/\/www.stoneharborhardware.com\/blogs\/articles\/choosing-the-correct-extended-lip-strike-size-for-your-door\" rel=\"nofollow noopener\" target=\"_blank\">guide to choosing an extended-lip strike size<\/a>. Its text identifies the screw-hole center to lip-end reference for the maker\u2019s range, and its linked measurement image depicts the stated reference. The page also discusses product sizes and finishes offered by that manufacturer. Those details are source-specific; they do not establish a general industry convention, a Koitor product, a door-system fit, or a performance result.<\/p>\n<p>The word <em>datum<\/em> means the defined point, line, surface, or feature used as the starting reference for a measurement. A buyer does not need to turn an RFQ into a metrology manual. The buyer does need to keep the start and end references attached to any dimension that will be used to compare parts. If a source does not state the datum, label it unknown and request a drawing or written clarification.<\/p>\n<p>This is especially useful when quotations arrive in different formats. One supplier may return a named catalog size; another may show an overall outline; a third may provide a drawing with dimension arrows but no clear label. The sourcing team should not normalize these values until it knows what each one measures. A numeric match is not evidence that two parts share the same geometry or application.<\/p>\n<h2>What is an extended strike plate size different from?<\/h2>\n<p>The term \u201cextended strike plate size\u201d can refer to different pieces of information depending on the source. A maker may define a nominal or named size according to one dimension, while also providing overall plate length, height, mounting-hole locations, opening geometry, corner profile, or other product details. A distributor\u2019s catalog may display just one of those values. Buyers should preserve the source\u2019s exact label and separately capture every dimension needed for product identification.<\/p>\n<p>For a B2B comparison, distinguish at least these fields:<\/p>\n<div class=\"wp-block-table koitor-responsive-table\" style=\"max-width:100%;overflow-x:auto;\">\n<table style=\"width:100%;border-collapse:collapse;overflow-wrap:anywhere;\">\n<thead>\n<tr>\n<th>Campo<\/th>\n<th>What it describes<\/th>\n<th>Acci\u00f3n del comprador<\/th>\n<\/tr>\n<\/thead>\n<tbody>\n<tr>\n<td>Catalog size label<\/td>\n<td>The maker\u2019s product-family name or nominal size<\/td>\n<td>Copy the exact label and model code; do not treat it as a complete drawing<\/td>\n<\/tr>\n<tr>\n<td>Size datum<\/td>\n<td>The start and end references used for the named dimension<\/td>\n<td>Ask the maker to state or show both references<\/td>\n<\/tr>\n<tr>\n<td>Overall envelope<\/td>\n<td>The outer dimensions of the complete plate<\/td>\n<td>Record it separately, with orientation and unit<\/td>\n<\/tr>\n<tr>\n<td>Mounting pattern<\/td>\n<td>The locations and pattern of the fixing features<\/td>\n<td>Use the current drawing or controlled measurement; do not infer from a photo<\/td>\n<\/tr>\n<tr>\n<td>Strike opening and outline<\/td>\n<td>The opening, lip, corners, and plate shape<\/td>\n<td>Identify the drawing revision and exact model<\/td>\n<\/tr>\n<tr>\n<td>Application identity<\/td>\n<td>The intended door, latch, and frame system<\/td>\n<td>Obtain confirmation from the responsible hardware or system supplier<\/td>\n<\/tr>\n<tr>\n<td>Included parts<\/td>\n<td>Screws or other items included in the quoted package<\/td>\n<td>Confirm sale-unit scope rather than assuming from an image<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<\/div>\n<p>The table is a buyer\u2019s record structure, not a universal list of dimensions or an installation instruction. Not every field will be applicable to every item. A field that is not provided should remain marked \u201cnot stated\u201d or \u201cnot applicable,\u201d rather than being filled from a different model or a visually similar product.<\/p>\n<p>Keep measurement and fit decisions separate. A buyer may know the exact distance shown on a drawing and still lack enough information to determine whether the part fits a particular assembly. The plate outline, door preparation, latch position, opening, mounting pattern, finish, and system requirements may matter in a specific application. The buyer should refer those questions to the qualified supplier or system specialist rather than infer compatibility from one dimension.<\/p>\n<p>The phrase \u201cextended\u201d also does not identify how much extension a particular part has or what the part will do in a particular installation. A longer labeled measurement is not automatically the right replacement, a performance improvement, or a security upgrade. Avoid selection instructions such as \u201cchoose the longest lip\u201d unless the responsible system documentation establishes that decision for the exact application.<\/p>\n<h2>How can importers compare two catalog offers accurately?<\/h2>\n<p>Compare the same measurement between offers. First record each supplier\u2019s exact code and revision. Next, copy the supplier\u2019s stated size label and record its measurement start and end. Then capture the overall outline and any mounting dimensions separately. Finally, note which fields are supported by current documentation and which still require an answer.<\/p>\n<p>Consider a hypothetical RFQ. Offer A provides a nominal label and a drawing that defines the distance from screw-hole centers to the lip end. Offer B provides an overall plate length but does not define its nominal label. The buyer cannot declare that the two values match because one is a datum-based distance and the other is edge-to-edge. The next action is to request Offer B\u2019s start and end references or a dimensioned drawing. This example does not describe a real supplier or a real second measurement convention.<\/p>\n<p>If a supplier uses a different orientation or reference, preserve it as written. Do not rename an overall length as a nominal size merely to fit the buyer\u2019s comparison spreadsheet. A normalization table can show both the original value and a separately calculated value only when a complete, controlled drawing provides all necessary references and a qualified reviewer approves the method. If the drawing is incomplete, retain the gap instead of deriving a dimension from a product photograph.<\/p>\n<p>A catalog-to-drawing comparison can use the following structure:<\/p>\n<div class=\"wp-block-table koitor-responsive-table\" style=\"max-width:100%;overflow-x:auto;\">\n<table style=\"width:100%;border-collapse:collapse;overflow-wrap:anywhere;\">\n<thead>\n<tr>\n<th>Record field<\/th>\n<th>Offer A<\/th>\n<th>Offer B<\/th>\n<th>Review status<\/th>\n<\/tr>\n<\/thead>\n<tbody>\n<tr>\n<td>Supplier, model, and revision<\/td>\n<td>Exact source reference<\/td>\n<td>Exact source reference<\/td>\n<td>Confirmed \/ unresolved<\/td>\n<\/tr>\n<tr>\n<td>Catalog size label<\/td>\n<td>Exact wording<\/td>\n<td>Exact wording<\/td>\n<td>Recorded \/ missing<\/td>\n<\/tr>\n<tr>\n<td>Measurement start<\/td>\n<td>Maker-stated datum<\/td>\n<td>Maker-stated datum<\/td>\n<td>Confirmed \/ unresolved<\/td>\n<\/tr>\n<tr>\n<td>Measurement end<\/td>\n<td>Maker-stated endpoint<\/td>\n<td>Maker-stated endpoint<\/td>\n<td>Confirmed \/ unresolved<\/td>\n<\/tr>\n<tr>\n<td>Referenced view<\/td>\n<td>Drawing number and view<\/td>\n<td>Drawing number and view<\/td>\n<td>Current \/ outdated \/ missing<\/td>\n<\/tr>\n<tr>\n<td>Overall dimensions<\/td>\n<td>Separately stated values and units<\/td>\n<td>Separately stated values and units<\/td>\n<td>Comparable \/ not comparable<\/td>\n<\/tr>\n<tr>\n<td>Mounting pattern<\/td>\n<td>Controlled document reference<\/td>\n<td>Controlled document reference<\/td>\n<td>Confirmed \/ system review needed<\/td>\n<\/tr>\n<tr>\n<td>Included components<\/td>\n<td>Quoted sale-unit scope<\/td>\n<td>Quoted sale-unit scope<\/td>\n<td>Confirmed \/ unresolved<\/td>\n<\/tr>\n<tr>\n<td>Responsible approval<\/td>\n<td>Buyer and supplier reviewer<\/td>\n<td>Buyer and supplier reviewer<\/td>\n<td>Recorded \/ pending<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<\/div>\n<p>This comparison is useful when a range manager maintains replacement records across several suppliers. The range manager can retain each supplier\u2019s original terminology while adding a shared set of buyer-side fields for search and comparison. That approach improves data consistency without rewriting one maker\u2019s definition as if it applied to every product in the category. It also makes later audits easier: a reviewer can trace a normalized field back to the original model and document rather than relying on an undocumented spreadsheet formula.<\/p>\n<p>Use \u201ccomparable\u201d only when the buyer has confirmed that the values refer to the same endpoints, orientation, units, model revision, and measurement subject. If one supplier describes the overall plate and the other gives a functional distance, the correct comparison status is \u201cnot comparable yet.\u201d This is a useful decision state; it tells the team precisely what information is missing.<\/p>\n<p>When dimensions are converted between units, retain the original source value and unit beside the conversion. Record rounding rules if the converted number will be used in a purchasing specification. A converted catalog label should not replace the manufacturer\u2019s original model identity. Dimensional normalization supports procurement; it does not grant approval to modify a part or substitute it in a door system.<\/p>\n<h2>What evidence should support the measurement record?<\/h2>\n<p>Use current, model-specific evidence. A supplier\u2019s product page may explain a catalog convention, while a dimensioned drawing can identify geometry for a specific part. A controlled sample can help resolve an identity question when it is labeled and linked to the approved model. A quotation may clarify what is included or which revision is being offered. Each source answers a different part of the buyer\u2019s question.<\/p>\n<p>For every value in the comparison record, keep the source beside it. Useful source references include a drawing number and revision, a dated product specification, an official maker page, or a written supplier response tied to the model code. If a measurement is taken from a physical sample, identify the measuring method and reviewer, and keep the sample traceable. Do not treat an uncontrolled sample from a mixed parts tray as an approved reference.<\/p>\n<p>The manufacturer\u2019s linked illustration is useful for understanding the maker\u2019s stated datum because it visually indicates the reference line in its own explanation. It is not a toleranced engineering drawing. It does not establish hidden geometry, an installed latch path, a universal clearance, or the dimensions of another supplier\u2019s part. A buyer can use it to understand the source\u2019s terminology, but not to measure pixels or derive a manufacturing requirement.<\/p>\n<p>An image of an installed product can help a buyer ask about visible placement. It cannot establish a dimension unless it is explicitly calibrated and supplied for that purpose. Perspective, camera angle, trim, door preparation, hardware orientation, and image scaling can distort apparent size. For dimensional comparison, request the source document that actually states the references.<\/p>\n<p>If a document conflicts with a product listing, record the conflict and ask the supplier which revision governs the quotation. Do not choose whichever value supports the desired comparison. If an existing replacement specification was created from an older product, preserve the prior source and mark it for review when the model, supplier, or drawing changes.<\/p>\n<p>Avoid using an individual part measurement to infer application performance. A dimension record does not establish latch engagement, security, fire-door suitability, code compliance, accessibility, or a particular door\u2019s compatibility. Those are separate questions, often with responsible parties and evidence beyond the plate\u2019s nominal size. Keep the record\u2019s conclusion narrow: \u201cmeasurement convention understood,\u201d \u201cdimensions comparable,\u201d or \u201csystem compatibility pending review.\u201d<\/p>\n<h2>What should a buyer do when the datum is missing?<\/h2>\n<p>Mark the size as unresolved and send the supplier a focused request. Identify the catalog model, quote line, and version under review. Ask where the size begins and ends, request the relevant drawing view, and ask for the overall plate dimensions separately. If mounting pattern or opening geometry is required for identification, request those fields as well, without implying that a dimensional response alone approves fit.<\/p>\n<p>A short clarification can be more effective than a broad request for \u201call specifications.\u201d For example: \u201cPlease identify the start and end references for the catalog size shown for this model and provide the current overall plate dimensions with drawing revision. Please confirm whether the quoted drawing applies to the offered finish and sale unit.\u201d This wording asks for supplier evidence while leaving the supplier responsible for its own definition.<\/p>\n<p>The buyer should also distinguish a missing answer from an answer that does not apply. If the product family does not publish a nominal size convention, record that the label is unavailable and use the controlled dimensions necessary for the buyer\u2019s comparison. If the supplier cannot provide a drawing or other reliable reference, the buyer may keep the item on hold or refer it to a technical reviewer. The article does not advise modifying, forcing, or installing a part while information is incomplete.<\/p>\n<p>After the supplier responds, update the comparison record and retain the response. Note who reviewed it, when it was accepted, and which model\/revision it covers. If a later order changes the part code, material, finish, supplier, or drawing revision, reopen the affected fields. An older datum explanation should not automatically be carried forward to a newly offered product.<\/p>\n<h2>Which questions remain separate from size comparison?<\/h2>\n<p>Understanding the size datum is one stage in identification, not a complete selection or installation decision. Keep adjacent questions visible so that procurement does not accidentally claim more than its evidence proves.<\/p>\n<ul>\n<li><strong>Overall fit:<\/strong> Does the complete part correspond to the intended door or frame? Ask the responsible system supplier.<\/li>\n<li><strong>Montaje:<\/strong> Does the mounting pattern match the prepared application? Use current controlled information and qualified review.<\/li>\n<li><strong>Latch relationship:<\/strong> Does the specific latch and receiving opening work as intended? A size label alone cannot establish this.<\/li>\n<li><strong>Finish and appearance:<\/strong> Does the offered finish match the buyer\u2019s approved sample and product record? Verify it under the project\u2019s process.<\/li>\n<li><strong>Security or fire performance:<\/strong> Is there product-specific evidence and authority for the claim? Do not infer it from lip length or a visible shape.<\/li>\n<li><strong>Replacement approval:<\/strong> Is the alternative model authorized for the application? Confirm with the system owner or responsible manufacturer.<\/li>\n<\/ul>\n<p>The buyer can choose a next-step status such as \u201csize datum confirmed,\u201d \u201coverall envelope incomplete,\u201d \u201cdrawing revision required,\u201d or \u201crefer for system compatibility review.\u201d These statuses make the supplier handoff actionable without pretending to resolve an engineering or compliance issue that the research does not cover.<\/p>\n<p>Keep any product listing consistent with the approved source. If a seller\u2019s public language uses a model-specific nominal size, avoid presenting the same label as a universal dimension. Include a model code or a clear product-specific reference where the buyer\u2019s system supports it. If the listing does not need a general compatibility claim, do not add one for SEO purposes.<\/p>\n<h3>How can Koitor discuss a related metal-component project?<\/h3>\n<p>Koitor Hardware is a family-owned factory and specialized OEM manufacturer focused on bathroom and home-storage metal hardware. Its approved company profile supports discussion of confirmed metal components, drawing or sample review, relevant forming and finishing questions, assembly, and packaging. It does not confirm that Koitor manufactures locks, residential strike plates, complete door sets, or any specific product from the cited supplier.<\/p>\n<p>The supplier\u2019s strike-size guide is an external example of a maker-defined measurement convention. It is not evidence about Koitor\u2019s product range or production record. Buyers should not infer capability from the fact that a referenced item is a metal plate. A project-specific scope review must happen before quotation, and security, fire, accessibility, installation, and system-compatibility conclusions remain with qualified parties responsible for the actual application.<\/p>\n<p>For an in-scope bathroom or home-storage project, buyers can share a lawful drawing or physical sample, required finish, packaging scope, target market, and expected quantity. Koitor can confirm whether the requested project fits its verified manufacturing scope before discussing next steps. The <a href=\"https:\/\/koitorhardware.com\/es\/fabricante-de-herrajes-para-el-hogar-de-marca-propia\/\" style=\"color:#0B5CAD;font-weight:600;text-decoration:underline;text-underline-offset:3px;\">OEM home-storage hardware overview<\/a> gives broader context but is not a catalog of all adjacent metal parts.<\/p>\n<h2>Buyer checklist before comparing extended strike plate offers<\/h2>\n<ul>\n<li>Capture each supplier\u2019s exact model code and revision.<\/li>\n<li>Copy the catalog size label without renaming it.<\/li>\n<li>Record the maker-stated start and end references for the label.<\/li>\n<li>Capture the overall plate dimensions separately, with units and orientation.<\/li>\n<li>Keep the source drawing or page attached to each value.<\/li>\n<li>Confirm that the drawing applies to the offered model and revision.<\/li>\n<li>Record the mounting pattern and other required dimensions from controlled evidence.<\/li>\n<li>Mark missing references as unknown; do not estimate from photography.<\/li>\n<li>Compare values only when the measurement endpoints and subjects match.<\/li>\n<li>Keep overall fit, latch function, installation, security, and fire questions separate.<\/li>\n<li>Identify who must resolve each open compatibility question.<\/li>\n<li>Reopen the record when a supplier, code, drawing, or revision changes.<\/li>\n<\/ul>\n<figure class=\"wp-block-image size-large koitor-blog-image\" style=\"margin:32px 0;\">\n  <img decoding=\"async\" src=\"https:\/\/koitorhardware.com\/wp-content\/uploads\/2026\/11\/K1631-process-delivery.webp\" alt=\"Buyer comparing a generic latch-receiver plate and its measurement references without textual labels\" style=\"width:100%;max-width:960px;height:auto;display:block;margin:0 auto;border-radius:10px;\"  srcset=\"https:\/\/koitorhardware.com\/wp-content\/uploads\/2026\/11\/K1631-process-delivery-18x10.webp 18w, https:\/\/koitorhardware.com\/wp-content\/uploads\/2026\/11\/K1631-process-delivery-150x150.webp 150w, https:\/\/koitorhardware.com\/wp-content\/uploads\/2026\/11\/K1631-process-delivery-300x169.webp 300w, https:\/\/koitorhardware.com\/wp-content\/uploads\/2026\/11\/K1631-process-delivery-768x432.webp 768w, https:\/\/koitorhardware.com\/wp-content\/uploads\/2026\/11\/K1631-process-delivery-1024x576.webp 1024w, https:\/\/koitorhardware.com\/wp-content\/uploads\/2026\/11\/K1631-process-delivery.webp 1200w\" sizes=\"(max-width: 1200px) 100vw, 1200px\" loading=\"lazy\"\/><figcaption style=\"font-size:14px;color:#667085;text-align:center;margin-top:8px;\">Record the measurement reference and the overall outline as separate fields.<\/figcaption><\/figure>\n<h2>Preguntas frecuentes<\/h2>\n<h3>Is the named size always the overall length of an extended strike plate?<\/h3>\n<p>No. The reviewed maker defines the nominal size for its own extended-lip family from a stated reference and separately describes overall length. Other suppliers may use different terms or references. Check the exact model\u2019s current documentation.<\/p>\n<h3>Do all manufacturers measure extended-lip strikes from screw-hole centers?<\/h3>\n<p>The cited manufacturer states that convention for its own range. The source does not establish a universal rule. Ask each supplier to identify the start and end references for the product being quoted.<\/p>\n<h3>Can a product photo establish the measurement datum?<\/h3>\n<p>Not reliably. A photo may help identify a question, but it does not normally provide a controlled scale or dimension reference. Use a dimensioned drawing, official product documentation, or a traceable supplier response.<\/p>\n<h3>If two strike plates have the same nominal size, are they interchangeable?<\/h3>\n<p>That conclusion does not follow from the shared label. The products may differ in overall outline, mounting pattern, opening, revision, or application. Obtain model-specific evidence and system-owner approval where compatibility matters.<\/p>\n<h3>Does a longer lip improve security or make a strike fit better?<\/h3>\n<p>No such conclusion follows from the nominal size alone. Security, fit, and performance depend on the complete product and application. Refer those decisions to the responsible supplier or qualified reviewer.<\/p>\n<figure class=\"wp-block-image size-large koitor-blog-image\" style=\"margin:32px 0;\">\n  <img decoding=\"async\" src=\"https:\/\/koitorhardware.com\/wp-content\/uploads\/2026\/11\/K1631-checklist-delivery.webp\" alt=\"Extended strike comparison record showing size label, start and end datums, orientation, and overall outline\" style=\"width:100%;max-width:960px;height:auto;display:block;margin:0 auto;border-radius:10px;\"  srcset=\"https:\/\/koitorhardware.com\/wp-content\/uploads\/2026\/11\/K1631-checklist-delivery-18x10.webp 18w, https:\/\/koitorhardware.com\/wp-content\/uploads\/2026\/11\/K1631-checklist-delivery-150x150.webp 150w, https:\/\/koitorhardware.com\/wp-content\/uploads\/2026\/11\/K1631-checklist-delivery-300x169.webp 300w, https:\/\/koitorhardware.com\/wp-content\/uploads\/2026\/11\/K1631-checklist-delivery-768x432.webp 768w, https:\/\/koitorhardware.com\/wp-content\/uploads\/2026\/11\/K1631-checklist-delivery-1024x576.webp 1024w, https:\/\/koitorhardware.com\/wp-content\/uploads\/2026\/11\/K1631-checklist-delivery.webp 1200w\" sizes=\"(max-width: 1200px) 100vw, 1200px\" loading=\"lazy\"\/><figcaption style=\"font-size:14px;color:#667085;text-align:center;margin-top:8px;\">A comparison sheet should keep the source label, reference points, and overall dimensions distinct.<\/figcaption><\/figure>\n<section class=\"koitor-blog-cta\" style=\"margin-top:42px;padding:28px;border:1px solid #D0D5DD;border-radius:16px;background:#F8FAFC;\">\n<h3 style=\"margin-top:0;margin-bottom:12px;font-size:28px;line-height:1.25;\">Discuss a Confirmed Metal Hardware Project<\/h3>\n<p style=\"font-size:16px;line-height:1.7;margin-bottom:20px;\">If your project involves a confirmed bathroom or home-storage metal component, send Koitor the relevant drawing or physical sample, finish requirement, packaging scope, target market, and expected quantity. Koitor can first confirm whether the project fits its verified manufacturing scope. Door-lock, strike-plate, security, fire, and installation decisions must be confirmed by the suppliers responsible for those systems.<\/p>\n<div style=\"display:flex;gap:12px;flex-wrap:wrap;\">\n    <a href=\"https:\/\/koitorhardware.com\/es\/contacto\/\" style=\"display:inline-block;padding:12px 20px;border-radius:8px;background:#FF5A1F;color:#ffffff;font-weight:700;text-decoration:none;\">Ponte en contacto con Koitor<\/a><br \/>\n    <a href=\"https:\/\/koitorhardware.com\/es\/\" style=\"display:inline-flex;align-items:center;justify-content:center;min-height:48px;padding:0 22px;border-radius:8px;border:1px solid #FF5A1F;color:#FF5A1F;background:#ffffff;font-weight:700;text-decoration:none;line-height:1;\">Descubre Koitor Hardware<\/a>\n  <\/div>\n<div class=\"koitor-article-tags\" style=\"display:flex;flex-wrap:wrap;gap:8px;margin-top:18px;\">\n    <span style=\"display:inline-flex;align-items:center;justify-content:center;padding:6px 12px;border-radius:999px;background:#FFF3ED;color:#FF5A1F;font-size:13px;font-weight:700;line-height:1.2;\">Gu\u00eda de compra para importadores<\/span><br \/>\n    <span style=\"display:inline-flex;align-items:center;justify-content:center;padding:6px 12px;border-radius:999px;background:#FFF3ED;color:#FF5A1F;font-size:13px;font-weight:700;line-height:1.2;\">Accesorios met\u00e1licos para almacenamiento<\/span><br \/>\n    <span style=\"display:inline-flex;align-items:center;justify-content:center;padding:6px 12px;border-radius:999px;background:#FFF3ED;color:#FF5A1F;font-size:13px;font-weight:700;line-height:1.2;\">Fabricaci\u00f3n por encargo (OEM) en lotes peque\u00f1os<\/span>\n  <\/div>\n<\/section>","protected":false},"excerpt":{"rendered":"<p>Compare an extended strike plate by recording the maker\u2019s size datum, the separate overall dimensions, model revision, and evidence before RFQ approval.<\/p>","protected":false},"author":1,"featured_media":8416,"comment_status":"closed","ping_status":"","sticky":false,"template":"","format":"standard","meta":{"footnotes":""},"categories":[145],"tags":[40,48,39],"class_list":["post-8419","post","type-post","status-publish","format-standard","has-post-thumbnail","hentry","category-hardware-sourcing-knowledge","tag-importer-buying-guide","tag-metal-storage-hardware","tag-small-batch-oem"],"_links":{"self":[{"href":"https:\/\/koitorhardware.com\/es\/wp-json\/wp\/v2\/posts\/8419","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/koitorhardware.com\/es\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/koitorhardware.com\/es\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/koitorhardware.com\/es\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/koitorhardware.com\/es\/wp-json\/wp\/v2\/comments?post=8419"}],"version-history":[{"count":1,"href":"https:\/\/koitorhardware.com\/es\/wp-json\/wp\/v2\/posts\/8419\/revisions"}],"predecessor-version":[{"id":8450,"href":"https:\/\/koitorhardware.com\/es\/wp-json\/wp\/v2\/posts\/8419\/revisions\/8450"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/koitorhardware.com\/es\/wp-json\/wp\/v2\/media\/8416"}],"wp:attachment":[{"href":"https:\/\/koitorhardware.com\/es\/wp-json\/wp\/v2\/media?parent=8419"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/koitorhardware.com\/es\/wp-json\/wp\/v2\/categories?post=8419"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/koitorhardware.com\/es\/wp-json\/wp\/v2\/tags?post=8419"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}