{"id":9435,"date":"2026-11-21T10:10:05","date_gmt":"2026-11-21T10:10:05","guid":{"rendered":"https:\/\/koitorhardware.com\/?p=9435"},"modified":"2026-11-21T10:11:59","modified_gmt":"2026-11-21T10:11:59","slug":"zinc-vs-nickel-plating","status":"publish","type":"post","link":"https:\/\/koitorhardware.com\/fr\/zinc-vs-nickel-plating\/","title":{"rendered":"Zinc vs Nickel Plating: Compare Protection and Finish Systems"},"content":{"rendered":"<p>Zinc vs nickel plating is not a simple choice between two colors: the coatings have different protection roles and can belong to different finish systems. Zinc on steel can act sacrificially as well as provide a barrier, while nickel is generally discussed as a barrier coating. Buyers should compare the named deposit, substrate, post-treatment, service environment and fit requirements, then identify what evidence applies to the actual component. A bright sample or familiar coating name alone does not establish service life or suitability.<\/p>\n<figure class=\"wp-block-image size-large koitor-blog-image\"><img decoding=\"async\" src=\"https:\/\/koitorhardware.com\/wp-content\/uploads\/2026\/11\/k1830-process-web.webp\" alt=\"An inspector compares two metal coating samples beside a cross-section diagram and product drawing.\" style=\"width:100%;max-width:960px;height:auto;display:block;margin:0 auto;\"  srcset=\"https:\/\/koitorhardware.com\/wp-content\/uploads\/2026\/11\/k1830-process-web-18x12.webp 18w, https:\/\/koitorhardware.com\/wp-content\/uploads\/2026\/11\/k1830-process-web-150x150.webp 150w, https:\/\/koitorhardware.com\/wp-content\/uploads\/2026\/11\/k1830-process-web-300x200.webp 300w, https:\/\/koitorhardware.com\/wp-content\/uploads\/2026\/11\/k1830-process-web-768x512.webp 768w, https:\/\/koitorhardware.com\/wp-content\/uploads\/2026\/11\/k1830-process-web-1024x683.webp 1024w, https:\/\/koitorhardware.com\/wp-content\/uploads\/2026\/11\/k1830-process-web.webp 1200w\" sizes=\"(max-width: 1200px) 100vw, 1200px\" loading=\"lazy\"\/><\/figure>\n<h2>What decision does this comparison help a buyer make?<\/h2>\n<p>An RFQ often contains a short finish note\u2014\u201czinc,\u201d \u201cnickel,\u201d or \u201csilver finish\u201d\u2014without enough detail to tell the manufacturer what the buyer intends. That can produce quotations that appear comparable but describe different systems. One supplier may quote an electroplated zinc deposit with a conversion treatment, another may quote an electrolytic nickel layer, and a third may be describing a zinc\u2013nickel alloy. These are not interchangeable names. Before comparing unit price, the buyer needs to establish what is being applied and what property the finish is supposed to serve.<\/p>\n<p>This guide is for product developers, importers, distributors and quality reviewers evaluating a finish on a metal component. The example could be a bracket, screw, hook, support or other hardware part; it is not a claim that every such part should receive either coating. The applicable substrate and duty matter. A decorative interior component, a fastener in a demanding assembly and a part exposed to repeated cleaning may face different requirements. No universal winner follows from the coating name.<\/p>\n<p>The comparison is also narrower than \u201cwhich metal is better?\u201d Zinc and nickel can appear in several processes and multilayer systems. Zinc\u2013nickel alloy plating combines zinc and nickel in a deposit; it is not the same as a zinc coating placed beside a separate nickel layer. Decorative nickel may be part of a nickel\/chrome system, which has its own appearance and specification questions. Electroless nickel is another distinct process family. A buyer should first make sure that two quotations actually refer to the same type of finish before comparing them.<\/p>\n<h2>What do zinc and nickel coatings do differently?<\/h2>\n<p>The key distinction in a steel application is the mechanism used to protect the substrate. Zinc coatings are commonly described as both a physical barrier and a sacrificial coating: zinc can preferentially corrode relative to the steel in the relevant electrochemical system. Nickel coatings are generally discussed as barrier coatings. That difference helps frame the questions, but it does not produce a service-life prediction for a particular finished part. Coating type, continuity, edges, geometry, post-treatment, assembly and the environment all matter.<\/p>\n<p>Barrier and sacrificial are descriptions of a protection mechanism, not an automatic pass\/fail guarantee. A barrier layer is intended to separate the underlying material from the environment. If a coating system has discontinuities, the exposed area and surrounding deposit may influence what happens; visual appearance alone cannot establish the extent or behavior of a defect. A sacrificial system uses a coating metal that can corrode preferentially under applicable conditions, but the specific result depends on the coating and exposure. Do not turn either general mechanism into an unqualified claim that a part will never rust or will last for a set number of years.<\/p>\n<p>The term \u201czinc coating\u201d also covers more than one application route. Electroplated zinc, hot-dip galvanized products and continuously coated sheet have different production contexts and should not be treated as though a result from one automatically applies to another. The <a href=\"https:\/\/galvanizeit.org\/corrosion\/corrosion-protection\/zinc-coatings\" rel=\"nofollow noopener\" target=\"_blank\">American Galvanizers Association overview of zinc coatings<\/a> distinguishes zinc-coating processes and describes the general protective role of zinc. It does not establish the performance of an unspecified electroplated component. The buyer must name the intended route and finish system.<\/p>\n<p>Nickel is not a single universal answer either. The word may refer to a deposit in a particular electroplating specification, a layer in a decorative stack, or a process such as electroless nickel. The substrate preparation, deposit structure and any additional layers can differ. A product comparison that says simply \u201cnickel is harder\u201d or \u201cnickel never corrodes\u201d is too broad to guide a purchase. Ask what nickel process and complete stack the supplier is quoting, and confirm that the quote and drawing use the same terminology.<\/p>\n<div class=\"wp-block-table koitor-responsive-table\" style=\"max-width:100%;overflow-x:auto;\">\n<table style=\"width:100%;border-collapse:collapse;overflow-wrap:anywhere;\">\n<thead>\n<tr>\n<th>RFQ field<\/th>\n<th>What the field clarifies<\/th>\n<th>What it cannot prove alone<\/th>\n<\/tr>\n<\/thead>\n<tbody>\n<tr>\n<td>Substrate and part form<\/td>\n<td>What material receives the coating and what geometry must be treated<\/td>\n<td>Finished performance or coating coverage<\/td>\n<\/tr>\n<tr>\n<td>Coating identity<\/td>\n<td>Whether the proposal is zinc, nickel, zinc\u2013nickel alloy or a multilayer system<\/td>\n<td>A particular service life<\/td>\n<\/tr>\n<tr>\n<td>Application route<\/td>\n<td>Which coating process and supplier scope are intended<\/td>\n<td>That another process will produce equivalent results<\/td>\n<\/tr>\n<tr>\n<td>Post-treatment or topcoat<\/td>\n<td>Which additional finish stages are included<\/td>\n<td>Compatibility with every exposure or cleaner<\/td>\n<\/tr>\n<tr>\n<td>Functional and cosmetic surfaces<\/td>\n<td>Which areas affect fit, appearance or assembly<\/td>\n<td>That a sample represents every production lot<\/td>\n<\/tr>\n<tr>\n<td>Acceptance evidence<\/td>\n<td>Which records or inspection apply to the order<\/td>\n<td>More than the defined scope of the evidence<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<\/div>\n<h2>How should a buyer compare finish proposals?<\/h2>\n<p>Start with the application rather than a generic ranking. Identify where the part will be used, what it contacts, how it is cleaned, how frequently it moves or is handled, and whether it is part of a larger assembly. A bathroom-related component may encounter moisture and cleaning, but the article does not assign a universal exposure class to \u201cbathroom.\u201d A buyer should describe the actual intended use and ask the responsible technical team to confirm which requirements are appropriate.<\/p>\n<p>Next, write the required appearance separately from the required function. A silver appearance does not identify the metal or process. Different coating systems can look similar in a photograph or under one lighting condition. If color or gloss matters, establish a controlled approved sample, relevant viewing conditions and how production variation will be reviewed. Treat a visual master as an appearance reference; it does not prove the coating composition, adhesion or corrosion behavior.<\/p>\n<p>Then compare the complete finish stack. Ask for the base material, coating identity, post-treatment, any topcoat or sealer, and the order of operations. If a supplier uses a commercial shorthand, request a plain-language definition and the controlled specification behind it. Record the answer in the drawing or purchase specification rather than leaving it in an email thread that may not follow a repeat order. If a product combines coated parts with screws or other hardware, confirm the finish for each component, not only the main body.<\/p>\n<p>Dimensional fit deserves a separate review. A coating adds material to surfaces and may affect close-fitting holes, threads, sliding interfaces or mating parts. The amount and distribution cannot be inferred from the word \u201cplating.\u201d Identify which dimensions are critical, whether threads are coated or masked, and which party owns final fit verification. A change from one coating proposal to another may require engineering review or a sample check, even when the color looks close. Do not prescribe an arbitrary thickness without consulting the responsible engineer and process supplier.<\/p>\n<p>Finally, decide what evidence is necessary. Depending on the product and purchase requirements, it may include a named specification, supplier process records, material or coating documentation, sample approval, defined inspection, or test evidence. A test name is not a complete acceptance criterion: specify the method, specimen or product, conditioning, evaluation criteria and responsible party as applicable. A result on a flat coupon does not automatically represent a complex finished geometry. Keep the requirement proportionate to the risk and let qualified technical owners define limits.<\/p>\n<h2>Zinc, nickel and zinc\u2013nickel are different descriptions<\/h2>\n<p>One recurring source of confusion is treating zinc\u2013nickel as a midpoint between zinc and nickel. It is a distinct alloy coating. It should be named as such in the drawing and supplier quotation. A zinc\u2013nickel proposal may have a different intended use and specification from either zinc-only or nickel-only plating; a buyer cannot infer equivalence from the two element names. The same discipline applies to multilayer finishes. A stack that contains nickel and chrome, for example, is not accurately described by the word \u201cnickel\u201d alone if the layer structure matters to the purchase.<\/p>\n<p>The coating name should answer \u201cwhat is being applied?\u201d It does not answer every other question: how the deposit is controlled, what areas are covered, what post-treatment is included, how appearance is accepted or how the finished component will behave in its actual environment. Keep those questions as distinct fields in the RFQ. The <a href=\"https:\/\/koitorhardware.com\/fr\/selective-plating-masking-boundaries-bathroom-hardware\/\">Selective plating boundaries for bathroom hardware<\/a> covers the separate alloy-versus-zinc comparison; it should not be read as proof that the alloy and nickel-metal coating in this article are synonymous.<\/p>\n<p>If a supplier uses shorthand such as \u201cNi,\u201d \u201cZn,\u201d \u201cwhite zinc,\u201d or \u201cnickel finish,\u201d ask for the full controlled description. Identify whether the shorthand refers to the base deposit, a post-treatment, a complete stack or a visual target. Clarification is especially useful when a prior sample or existing product uses a different finish and the buyer is trying to preserve the appearance while changing a process. A finish substitution is an engineering change, not merely a naming edit.<\/p>\n<h2>What can go wrong when the finish is underspecified?<\/h2>\n<p>The first risk is quote mismatch. A buyer compares two prices without noticing that one quotation includes post-treatment and another does not, or that suppliers interpret \u201cnickel\u201d differently. The quotes may not represent the same material, process stages or acceptance scope. A short clarification table\u2014substrate, coating, post-treatment, appearance, critical dimensions, inspection and documentation\u2014makes differences visible before a purchase order is issued.<\/p>\n<p>The second risk is choosing by color. A polished or bright sample can look convincing but does not independently show coating identity, thickness, adhesion, coverage or corrosion response. Even a color match can change under another light source or after the production route changes. Separate visual approval from functional requirements, and identify what evidence supports each one.<\/p>\n<p>The third risk is assuming a general protection statement applies to the finished product. A coating&#8217;s broad mechanism cannot replace an application-specific assessment. Edges, cavities, threaded areas, joins, contact points and post-processing can create conditions different from a flat sample. If the intended environment includes moisture, salts, chemicals, abrasive contact or repeated cleaning, describe it accurately and seek technical review. Do not convert a general article into a warranty or promise.<\/p>\n<p>The fourth risk is overlooking fit and assembly. Coating can affect interfaces, and a revised process can change the dimensions available for assembly. Threads, slots, press fits and close clearances should be reviewed on the actual drawing. A package may also combine components from several sources; a finish change on one part can create a mismatch with neighboring parts. Define the affected revision and check a representative assembly where appropriate.<\/p>\n<p>The fifth risk is losing control during reorders. A verbal approval may not identify the sample revision, coating route or post-treatment. A later order may follow a new vendor&#8217;s interpretation. Record the approved finish wording, reference sample, order linkage and any controlled deviations. If the technical scope changes, obtain approval before mass production rather than relying on a previous product photo.<\/p>\n<h3>How should samples, testing and records be interpreted?<\/h3>\n<p>A sample is useful for assessing the represented item, but its evidentiary scope is limited. Confirm whether it is a process sample, a pre-production sample, a production-intent part or a finished article from a previous order. Ask which material and finishing route were used and whether the critical surfaces and post-treatment match the proposed order. A sample with no traceable description can help discuss appearance, but it cannot settle an unidentified coating requirement.<\/p>\n<p>If a test is requested, avoid specifying only a number of hours or a test name without agreement on method and evaluation. The relevant stakeholders should decide the test purpose, specimens, preparation, product geometry, conditioning and acceptance rules. Results are tied to those conditions; they should not be translated directly into an expected field life unless a justified correlation exists for the actual product and environment. A test result also should not be transferred from one coating method to another by similarity of color or chemistry words.<\/p>\n<p>For records, establish the lot or order connection and the document owner. A generic brochure may explain a process, while a certificate or inspection record may address a specific material, coating or batch. Determine what the supplier can actually provide and what your quality plan requires. Avoid asking for evidence that no one has agreed to interpret, and do not claim an unverified record proves a property outside its scope.<\/p>\n<h3>How can an OEM review support a practical decision?<\/h3>\n<p>A custom metal hardware project may involve design, forming, joining, polishing, coating, assembly and packaging across different production responsibilities. A factory reviewing a drawing or sample can help identify where the finish specification intersects with geometry, weld access, mating dimensions and pack-out. That review is a coordination step; it does not itself certify a coating supplier or establish an untested performance claim.<\/p>\n<p>For a small-batch OEM project, the buyer can send the part drawing or physical sample, intended use, approved appearance reference, critical fit dimensions and known inspection requirements. Ask the manufacturer to confirm which process stages are in its scope and which are handled by a specialized finishing supplier. Make the assigned responsibility visible. If the finish is not yet selected, record the alternatives under review and the questions still requiring technical approval.<\/p>\n<p>Koitor Hardware is a family-owned custom metal hardware factory. Buyers can discuss drawing or sample customization, production sequence, finishing coordination, assembly and packaging preparation with the team. That statement does not mean every coating is performed in-house or that every proposed finish is available for every design. The actual product, supplier route and evidence must be confirmed for a project. For broader OEM discussion, see the <a href=\"https:\/\/koitorhardware.com\/fr\/oem-home-storage-hardware-manufacturer\/\">custom home storage hardware manufacturer page<\/a>. For decorative layer terminology, see the separate <a href=\"https:\/\/koitorhardware.com\/fr\/copper-undercoat-nickel-chrome-plating-bathroom-hardware\/\">Copper undercoat in nickel chrome plating<\/a>.<\/p>\n<h3>Build a finish decision record<\/h3>\n<p>A finish decision record should make the agreed system understandable to someone who did not attend the original supplier call. Begin with the part number and drawing revision, then list the substrate, coating identity, application route, post-treatment, appearance target and any protected interfaces. Add the intended use in plain language and note the conditions that were considered. If the requirement came from a customer, identify that source rather than translating it into a generic performance promise.<\/p>\n<p>Keep each evidence item matched to a claim. A certificate or supplier statement may identify a process or material; a sample may show appearance; a dimensional inspection may address a fit feature; a test report may address one defined method and specimen. The record should say what each item proves and what remains outside its scope. This prevents a file folder containing many documents from being mistaken for complete evidence when no document actually addresses the buyer\u2019s critical question.<\/p>\n<p>The record should also identify the parties. Note who supplies the substrate, who applies the coating, who performs any post-treatment and who approves the finished part. If the manufacturing factory coordinates an outside finisher, document the handoff and the record that returns with the lot. Do not state that a factory performs a process in-house unless that fact is confirmed for the order.<\/p>\n<p>For repeat orders, compare the new proposal against the approved record rather than only against the prior product photograph. A supplier, finish route, part geometry or post-treatment may have changed. Route material deviations through the agreed approval process, and preserve the final accepted wording with the purchase order. If a question remains open, label it as open; a transparent pending item is safer than an inferred equivalence.<\/p>\n<p>This disciplined record helps procurement compare proposals and helps quality review what will arrive. It does not replace engineering judgment or guarantee product performance. Its purpose is to make the coating system, responsibilities and evidence traceable from the original buyer requirement through production and reorder.<\/p>\n<h2>Buyer checklist before approving a quote<\/h2>\n<ul>\n<li>Name the substrate, component and governing drawing revision.<\/li>\n<li>Write \u201czinc,\u201d \u201cnickel,\u201d \u201czinc\u2013nickel alloy,\u201d or the intended multilayer stack precisely.<\/li>\n<li>Identify the application route and every post-treatment or topcoat included.<\/li>\n<li>Describe the service environment and cleaning or contact conditions that matter.<\/li>\n<li>Separate appearance targets from functional and corrosion-related requirements.<\/li>\n<li>Mark critical threads, holes, mating faces and dimensions that may be affected by coating.<\/li>\n<li>Define the approved appearance sample and how production variation will be reviewed.<\/li>\n<li>Agree on any test method, specimen, evaluation and acceptance owner before ordering.<\/li>\n<li>Identify the records required and how they will be tied to the production lot.<\/li>\n<li>Confirm who performs each finishing stage and who resolves a process deviation.<\/li>\n<li>Record the approved stack and sample revision for reorder control.<\/li>\n<li>Escalate safety, regulatory or product-performance requirements to the qualified responsible reviewer.<\/li>\n<\/ul>\n<h2>Foire aux questions<\/h2>\n<h3>Is zinc\u2013nickel the same as nickel plating?<\/h3>\n<p>No. Zinc\u2013nickel refers to an alloy coating containing zinc and nickel, while \u201cnickel plating\u201d can refer to other coating systems. Specify the exact deposit and process instead of treating the names as synonyms.<\/p>\n<h3>Does a silver-looking finish identify whether a part is zinc-plated or nickel-plated?<\/h3>\n<p>No. Appearance alone is not a reliable identification of the coating system. Use the supplier&#8217;s controlled description and appropriate records for the actual part.<\/p>\n<h3>Is nickel always more corrosion resistant than zinc?<\/h3>\n<p>That conclusion is too broad. Zinc and nickel have different protection mechanisms, and results depend on the complete system, substrate, geometry, post-treatment and environment. Compare defined proposals against the product requirement.<\/p>\n<h3>Can a finish be changed after the sample is approved?<\/h3>\n<p>Treat a changed coating or post-treatment as a controlled engineering change. Review appearance, fit, assembly and relevant evidence, then approve the revised scope before production.<\/p>\n<h2>Work with Koitor Hardware<\/h2>\n<p>If you are comparing zinc and nickel finish proposals for a metal hardware product, share the drawing or sample, intended application, critical fit features and the exact finish wording under review. Koitor can discuss the manufacturing sequence and project scope for customized bathroom and home-storage hardware. A project-specific review should identify what is known, what belongs to the finishing supplier and what still needs technical approval. Contact the team through the <a href=\"https:\/\/koitorhardware.com\/fr\/oem-home-storage-hardware-manufacturer\/\">OEM home storage hardware page<\/a> with those details.<\/p>\n<figure class=\"wp-block-image size-large koitor-blog-image\"><img decoding=\"async\" src=\"https:\/\/koitorhardware.com\/wp-content\/uploads\/2026\/11\/k1830-checklist-web.webp\" alt=\"Buyer review desk with substrate, coating, appearance reference and inspection notes arranged separately.\" style=\"width:100%;max-width:960px;height:auto;display:block;margin:0 auto;\"  srcset=\"https:\/\/koitorhardware.com\/wp-content\/uploads\/2026\/11\/k1830-checklist-web-18x12.webp 18w, https:\/\/koitorhardware.com\/wp-content\/uploads\/2026\/11\/k1830-checklist-web-150x150.webp 150w, https:\/\/koitorhardware.com\/wp-content\/uploads\/2026\/11\/k1830-checklist-web-300x200.webp 300w, https:\/\/koitorhardware.com\/wp-content\/uploads\/2026\/11\/k1830-checklist-web-768x512.webp 768w, https:\/\/koitorhardware.com\/wp-content\/uploads\/2026\/11\/k1830-checklist-web-1024x683.webp 1024w, https:\/\/koitorhardware.com\/wp-content\/uploads\/2026\/11\/k1830-checklist-web.webp 1200w\" sizes=\"(max-width: 1200px) 100vw, 1200px\" loading=\"lazy\"\/><\/figure>\n<p>In practical sourcing, <strong>zinc vs nickel plating<\/strong> should frame a defined comparison; the purchase specification still needs the exact material or process, acceptance criteria, and evidence required for the actual part.<\/p>\n<h3>Sources<\/h3>\n<ul>\n<li><a href=\"https:\/\/galvanizeit.org\/corrosion\/corrosion-protection\/zinc-coatings\" rel=\"nofollow noopener\" target=\"_blank\">American Galvanizers Association: Zinc Coatings<\/a><\/li>\n<li><a href=\"https:\/\/www.electroniquel.es\/?lang=en\" rel=\"nofollow noopener\" target=\"_blank\">\u00c9lectronique L: Surface treatment overview<\/a><\/li>\n<li><a href=\"https:\/\/kcjplating.com\/nickel-plating-vs-zinc-plating\/\" rel=\"nofollow noopener\" target=\"_blank\">KC Jones Plating: Nickel Plating vs. Zinc Plating<\/a><\/li>\n<\/ul>\n<section class=\"koitor-blog-cta\" style=\"margin:32px 0;padding:28px;border:1px solid #e8e8e8;border-radius:12px;background:#fafafa;\">\n<h3 style=\"margin-top:0;\">Discuss Your zinc vs nickel plating Requirements<\/h3>\n<p>Share the controlled drawing or sample, intended use and the specific question you are resolving. Koitor can discuss relevant metal hardware manufacturing scope and identify details that need confirmation for your project.<\/p>\n<div style=\"display:flex;flex-wrap:wrap;gap:12px;margin:20px 0;\">\n<a href=\"https:\/\/koitorhardware.com\/fr\/contact\/\" style=\"display:inline-flex;align-items:center;justify-content:center;background:#FF5A1F;color:#ffffff;padding:12px 20px;border-radius:6px;text-decoration:none;font-weight:600;\">Send a Drawing or Sample<\/a><br \/>\n<a href=\"https:\/\/koitorhardware.com\/fr\/oem-home-storage-hardware-manufacturer\/\" style=\"display:inline-flex;align-items:center;justify-content:center;background:#ffffff;color:#FF5A1F;border:1px solid #FF5A1F;padding:12px 20px;border-radius:6px;text-decoration:none;font-weight:600;\">Examen des capacit\u00e9s des \u00e9quipementiers<\/a>\n<\/div>\n<div class=\"koitor-article-tags\" style=\"display:flex;flex-wrap:wrap;gap:8px;margin-top:16px;\">\n<span style=\"display:inline-flex;background:#FFF3ED;color:#B83B12;padding:6px 10px;border-radius:999px;font-size:13px;\">Quincaillerie de rangement en m\u00e9tal<\/span><br \/>\n<span style=\"display:inline-flex;background:#FFF3ED;color:#B83B12;padding:6px 10px;border-radius:999px;font-size:13px;\">Guide d'achat pour les importateurs<\/span><br \/>\n<span style=\"display:inline-flex;background:#FFF3ED;color:#B83B12;padding:6px 10px;border-radius:999px;font-size:13px;\">Contr\u00f4le qualit\u00e9<\/span>\n<\/div>\n<\/section>","protected":false},"excerpt":{"rendered":"<p>Zinc and nickel are different coating proposals. Compare substrate, protection role, appearance, post-treatment, exposure and dimensional fit instead of choosing from color alone.<\/p>","protected":false},"author":1,"featured_media":9432,"comment_status":"closed","ping_status":"closed","sticky":false,"template":"","format":"standard","meta":{"footnotes":""},"categories":[145],"tags":[40,48,37],"class_list":["post-9435","post","type-post","status-publish","format-standard","has-post-thumbnail","hentry","category-hardware-sourcing-knowledge","tag-importer-buying-guide","tag-metal-storage-hardware","tag-quality-control"],"_links":{"self":[{"href":"https:\/\/koitorhardware.com\/fr\/wp-json\/wp\/v2\/posts\/9435","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/koitorhardware.com\/fr\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/koitorhardware.com\/fr\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/koitorhardware.com\/fr\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/koitorhardware.com\/fr\/wp-json\/wp\/v2\/comments?post=9435"}],"version-history":[{"count":1,"href":"https:\/\/koitorhardware.com\/fr\/wp-json\/wp\/v2\/posts\/9435\/revisions"}],"predecessor-version":[{"id":9472,"href":"https:\/\/koitorhardware.com\/fr\/wp-json\/wp\/v2\/posts\/9435\/revisions\/9472"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/koitorhardware.com\/fr\/wp-json\/wp\/v2\/media\/9432"}],"wp:attachment":[{"href":"https:\/\/koitorhardware.com\/fr\/wp-json\/wp\/v2\/media?parent=9435"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/koitorhardware.com\/fr\/wp-json\/wp\/v2\/categories?post=9435"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/koitorhardware.com\/fr\/wp-json\/wp\/v2\/tags?post=9435"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}