Startseite
Produkte
Aufbewahrung im Badezimmer Aufbewahrung in der Küche Duschablagen Drahtkörbe Handtuchhalter Alle Produkte anzeigen
Maßanfertigung Fabrik Qualität Blog Kontakt

Kenntnisse in der Hardware-Beschaffung

Metric Bolt Size Chart: Common Diameter and Pitch References

The M number identifies nominal thread diameter and the following pitch value identifies thread spacing in millimeters. A bolt size chart does not set head, wrench, hole, tolerance or strength requirements.

Metric bolts in multiple diameters beside a thread pitch gauge and engineering drawing

This metric bolt size chart lists selected common nominal diameters and thread pitches in millimeters: M3 × 0.5, M4 × 0.7, M5 × 0.8, M6 × 1.0, M8 × 1.25, M10 × 1.5 and M12 × 1.75. In each pair, the M number identifies nominal thread diameter and the value after the multiplication sign is pitch. These are reference entries, not a complete standard table or acceptance limits. A complete fastener callout also needs the part form, length, material or property class where specified, and the controlled drawing requirements.

Diagram separating metric bolt nominal diameter, thread pitch, length and head style
Diameter, pitch, length and head style describe different fastener attributes.

Metric bolt size chart: selected diameter and pitch pairs

The selected entries below are common coarse-pitch references shown in a supplier’s metric thread chart. They help readers interpret the basic designation. The source chart, published by Lexco Cable, includes additional entries and alternatives; only the seven selected pairs are reproduced here. The supplier table is a convenient reference, not a substitute for the fastener supplier’s controlled data or the complete applicable standard.

Metric designation Nominal thread diameter Selected pitch Buyer reading
M3 × 0.5 3 mm 0.5 mm Nominal diameter 3 mm; thread spacing 0.5 mm
M4 × 0.7 4 mm 0.7 mm Nominal diameter 4 mm; thread spacing 0.7 mm
M5 × 0.8 5 mm 0.8 mm Nominal diameter 5 mm; thread spacing 0.8 mm
M6 × 1.0 6 mm 1.0 mm Nominal diameter 6 mm; thread spacing 1.0 mm
M8 × 1.25 8 mm 1.25 mm Nominal diameter 8 mm; thread spacing 1.25 mm
M10 × 1.5 10 mm 1.5 mm Nominal diameter 10 mm; thread spacing 1.5 mm
M12 × 1.75 12 mm 1.75 mm Nominal diameter 12 mm; thread spacing 1.75 mm

The multiplication sign separates attributes; it is not a multiplication operation. “M6 × 1.0” identifies a nominal thread size and pitch. It does not tell you the bolt’s length, head type, under-head length convention, wrench dimension, clearance-hole size, tap-drill size, material or property class.

A chart can include multiple pitches for the same nominal diameter. The table above is deliberately selective and should not be read as a claim that each diameter has only one pitch. If a fastener’s full designation includes another pitch, confirm that combination in the supplier’s controlled information and project specification. Do not select an alternative simply because it appears in a generic internet chart.

Using a metric bolt size chart without overreading it

The seven rows are a quick orientation reference for common diameter-and-pitch pairs, not a selection algorithm. First compare the drawing callout with the relevant row. If the callout includes a pitch that is not shown here, do not assume it is invalid; consult the specified fastener standard, supplier catalog or design owner. If the callout gives only a diameter, the chart cannot determine which pitch the mating component requires.

The source for these selected pairs is the metric thread reference published by Lexco Cable. Its PDF contains a larger set of entries and other columns. This article reproduces only seven short diameter/pitch pairs and does not reproduce the complete table, rounded inch equivalents or drilling recommendations. A source table can be useful for an initial check, but a buyer should compare the exact part against the fastener supplier’s controlled data and the project drawing. The PDF did not state a publication date; its hosting folder date is not treated as a refresh date.

When a supplier uses a different notation, ask for the meaning of each field instead of converting the label by guesswork. Confirm whether the supplier is quoting the same thread family and pitch, then compare the remaining dimensions from the drawing. A familiar-looking M value alone is not enough to release a purchase.

Is the M number the wrench size?

No. The M number refers to nominal thread diameter, not the head’s across-flats dimension or the tool size. Head dimensions depend on the applicable fastener design and standard. Check the actual supplier drawing or specification.

How to read a metric bolt callout

A typical illustrative callout might read M6 × 1.0 × 20. In a common notation, that can be read as nominal 6 mm thread diameter, 1.0 mm pitch and a stated 20 mm length. The length measurement convention depends on head style and applicable specification, so the buyer should verify how length is defined for the exact fastener. The example is for reading fields, not a complete engineering order.

A drawing or purchase specification may also identify the head style, drive type, thread length, point, washer, coating, material, property class and acceptance requirements. Those details are not encoded in the M-size pair alone. A bolt with the right nominal diameter and pitch can still be the wrong component if its length, head clearance, drive recess, finish or mating interface differs.

Callout field What it tells the buyer What to verify separately
M designation and nominal diameter Nominal thread size family Full supplier designation and applicable system
Pitch after the M value Thread spacing Whether the specified pitch is correct for the mating part
Length A stated fastener dimension Measurement convention for the head style and drawing
Head style General head form Exact dimensions, clearance and approved part specification
Drive Recess or tool engagement type Supplier data and assembly tool compatibility
Material/property marking A separate material or mechanical classification when specified Governing standard, supplier documentation and buyer requirements
Finish or coating Surface condition or protection requirement Color, thickness or performance requirements where applicable
Quantity and packaging Commercial delivery scope Lot identification, pack quantity and documentation

A chart is useful for the thread-size fields only. It should not be used to invent the other rows. If the buyer’s drawing lacks a required field, flag it for the responsible engineer or product owner rather than allowing a supplier to assume one.

Pitch is different from diameter and thread fit

Nominal diameter and pitch work together to describe a thread size. Diameter is the nominal size category; pitch is the distance between corresponding points on adjacent threads, expressed in millimeters for this metric chart. Pitch can be measured or checked with an appropriate gauge, but a visual comparison cannot establish every tolerance or fit requirement.

Different fasteners can share a nominal diameter and use different pitches. Therefore, “M6” by itself may be insufficient where the mating thread matters. The buyer should state the complete required callout, not just the M number, and confirm the mating part uses the same intended thread system. This is particularly important when metal brackets, inserts, nuts or threaded plates come from different suppliers.

A pitch gauge can help identify candidate spacing, but it is not a substitute for controlled fastener data or a full inspection plan. A fit check by hand may show that two parts engage initially; it does not prove full thread compatibility, strength, correct length or acceptance. If a fastener is safety-critical or carries a specified load, the responsible technical reviewer must define the complete requirement and verification method.

Nominal reference versus measured acceptance

The numbers in the table are nominal references. They are not measured acceptance limits for a finished thread. A thread inspection requirement needs its own governing specification, tolerance class, measurement method, sampling plan and acceptance authority. The correct method depends on the thread and the buyer’s product requirement. Do not infer these values from a lookup chart or from the visible spacing of a few threads.

This distinction matters when several suppliers contribute to one assembly. A bolt maker may control the fastener dimensions, while a separate component supplier produces the nut, insert or tapped plate. The buyer’s product drawing should identify the intended interface and the responsible source should confirm compatibility. If the receiving feature is custom, ask the design owner to define its thread and acceptance basis before either supplier treats a trial assembly as final approval.

If an inspector uses a pitch gauge to identify an unknown fastener, document the method and result as an identification check only. Do not describe it as proof of compliance unless the purchase specification makes that method part of the acceptance plan. A visual or hand-fit check can be a useful screening step, but it cannot establish every dimension or mechanical property.

Some web charts mix coarse and fine pitches, imperial conversions, drill recommendations and head dimensions. These columns answer different questions and may have different sources or assumptions. This article does not reproduce tapping-drill sizes, wrench sizes, torque values, thread tolerances or inch conversions. Verify each requirement from the applicable controlled source.

Compare a fastener proposal against the mating assembly

For an importer sourcing metal bathroom or home-storage hardware, the screw or bolt is one part of a connection. The mating feature could be a threaded insert, nut, tapped plate, bracket, mounting point or purchased component. The buyer should compare the fastener callout against the controlled assembly drawing and the actual mating part.

Start with the complete specified thread: nominal diameter, pitch and thread length where relevant. Then check the bolt length and the geometry it must reach. Does the head sit on an external surface, enter a counterbore, or pass through a bracket? Does the assembly need clearance behind the mounting plate? Is the screw intended to be removable? These are product design questions and should be answered from the drawing, not from a size chart.

Next, define the head and drive. If the head must fit into a recess or remain below a cosmetic face, the head dimensions and clearance matter. If assembly uses a particular driver, confirm the drive type and access. Neither follows from the M designation. The same nominal thread can appear with different head styles and lengths.

Finally, confirm supplier and lot information. If the bolt is supplied as a bought-in part, identify its manufacturer or source as required by the project and the material/property documentation requested. If a substitution is proposed, compare every controlled field and obtain approval. A part number that looks close is not enough to prove interchangeability.

Does one metric diameter have only one possible pitch?

No. Some nominal diameters can have more than one pitch option. Use the complete callout and verify it against the supplier’s controlled information and the mating component.

Resolve conflicting thread references before purchase

If two public charts show different pitches for what appears to be the same nominal diameter, pause before choosing either value. The charts may use different thread families, include a fine-pitch alternative, contain a transcription error or omit the context that defines the row. Confirm the complete fastener designation with the supplier and compare it with the controlled drawing and mating component. A search result or copied table is not an approval authority.

For a buyer, the practical resolution is a short written clarification. Ask the fastener supplier to identify the designation system, the exact diameter and pitch, the part number, and the product data or standard used for the quotation. Ask the mating-part supplier or design owner to confirm that the intended thread is the same. Save both confirmations with the revision-controlled order documents. If a component has already been sampled, verify that the sample’s identification and thread match the written callout before it becomes the reference item.

Do not average values, select the most common-looking row or infer a pitch from a wrench chart. A wrench chart covers a different dimension. Likewise, a tapping recommendation may be based on a particular material and process and is outside this article’s scope. If the drawing itself is incomplete, return the question to the designer rather than having the supplier silently choose a thread.

When an error is found after a quote has been issued, identify whether the mistake affected only the reference explanation or changed the actual part number and mating feature. Correct the documentation, notify all suppliers who rely on the old revision, and assess any sample or purchase already in progress. This is a document-control action; the size chart alone cannot decide whether a production part should be accepted.

Common metric bolt chart mistakes

Treating M6 as a complete order description. It gives a nominal thread diameter family but omits pitch, length, head style and other requirements.

Reading pitch as bolt length. The pitch value describes spacing between threads, not the length of the fastener.

Treating the M number as the head or wrench size. Thread diameter and head dimensions are separate attributes.

Assuming the common listed pitch is the only option. A chart may omit less common or fine-pitch entries. Confirm the exact specified combination.

Using a generic chart as a tolerance specification. A nominal diameter/pitch lookup does not establish finished thread tolerances or inspection limits.

Using a chart for a drill or torque instruction. Those are different technical questions and need their own approved source and product context.

Assuming a matching pitch proves the bolt fits. Length, thread form, mating component, head clearance, finish and the controlling specification also matter.

Accepting an alternative without review. An alternate bolt can change fit, assembly, appearance or performance. Document the change and obtain approval from the responsible design owner.

Does a size chart set thread acceptance tolerances?

No. It provides nominal references. Acceptance tolerances and inspection requirements come from the applicable controlled specification and the purchase or drawing requirements.

Buyer checklist for fastener RFQs

Before sending an RFQ or accepting a fastener sample, confirm:

  1. Nominal thread diameter and exact pitch.
  2. Thread system and applicable supplier or drawing reference.
  3. Fastener type and head style.
  4. Length and the measurement convention for that head.
  5. Threaded length and any unthreaded shank requirement.
  6. Drive type and access space.
  7. Material or property class where the design specifies it.
  8. Finish, coating or color requirement where applicable.
  9. Mating component, insert or threaded feature.
  10. Required documentation and lot identification.
  11. Approved sample or drawing revision.
  12. Who reviews and approves a proposed substitution.

This checklist is intended to make quotations comparable. Do not add a material grade, strength class, torque, clearance hole or drill size from a general size chart unless the project’s technical owner has specified it. If a field is undecided, mark it as an open requirement and ask the responsible designer to resolve it.

A useful drawing callout is clear enough that two suppliers would quote the same fastener. It should identify the fastener family, complete thread, length, head and drive, plus any project-specific material, finish or documentation requirements. Attach an assembly drawing where the fastener interacts with a bracket, insert or cosmetic face. This reduces reliance on shorthand and helps the supplier flag conflicts before production.

For repeat orders, preserve the approved fastener part number, drawing revision, supplier reference and mating component together. If the source changes, compare the actual specification rather than just the trade name or packaging label. A replacement bolt can have the same nominal thread but a different head, length, finish or property marking. The buyer should route any difference to the person authorized to approve the assembly. That decision can then be repeated reliably when a product is reordered or another supplier is added.

When the exact fastener is not available, ask the supplier to list the proposed alternative field by field. A change in pitch can affect thread engagement; a change in length can affect clearance or protrusion; a change in head may interfere with a visible face or adjacent part; and a change in material or finish may raise separate project questions. These are reasons to review the change, not automatic predictions of failure. The responsible engineer should assess the actual design and decide whether the alternative is acceptable.

Buyer checking metric bolt diameter, thread pitch, length and mating-component details
Record the complete fastener and mating-part requirements before comparing quotations.

What Koitor can clarify in a hardware assembly

Koitor is a family-owned custom metal bathroom and home-storage hardware factory supporting customization from buyer drawings or physical samples, along with relevant forming, joining, finishing, assembly and packaging work. The available company facts do not establish that Koitor manufactures every fastener type or provides a thread laboratory or engineering certification service.

If a metal hardware assembly includes purchased fasteners, the buyer can provide the controlled product drawing, fastener callout, mating component and unresolved fit question. Koitor can review the assembly context within its approved manufacturing scope and help identify information that needs confirmation from the fastener supplier or buyer’s technical authority. That review does not convert a generic chart into a product approval or prove that an unspecified bolt will meet a load requirement.

Keep the approved fastener information with the assembly revision. If a supplier changes the pitch, head, finish or source, review the change against the mating feature and assembly sequence. A screw that appears close to the original may still create a fit or production issue. Document the approved alternative and the evidence that supports it.

Häufig gestellte Fragen

What does M8 × 1.25 mean?

It identifies a nominal metric thread diameter of 8 mm and a pitch of 1.25 mm in the selected reference notation. It does not define the bolt length, head or strength class.

Is an M6 bolt 6 mm long?

No. M6 refers to nominal thread diameter. Length is a separate dimension, often written separately in a complete callout.

Can I use a size chart to choose a replacement bolt?

A chart can help identify nominal diameter and pitch. To choose a replacement, also confirm length, head, drive, material or property requirements, finish and the mating part. Have the responsible technical owner approve substitutions.

Does a metric size chart tell me the wrench size?

No. Wrench dimensions depend on head style and the applicable fastener specification. Check the supplier’s drawing or controlled product data.

Are the listed pitches exhaustive?

No. This article includes seven selected common reference pairs only. The supplier source lists additional entries and alternatives. Verify the exact requirement in controlled fastener information.

Arbeiten Sie mit Koitor Hardware zusammen

If your bathroom or home-storage product uses a fastener that must fit a custom metal assembly, share the current drawing, complete bolt callout and mating-part details. Koitor can review the metal hardware manufacturing context within its stated OEM scope. Confirm fastener specifications, property requirements and substitutions with the responsible fastener supplier and technical authority.

Review a Fastener-to-Hardware Interface

Send the assembly drawing or sample, the complete fastener callout and the mating-part question. Koitor can clarify the hardware manufacturing scope while your supplier confirms the controlled fastener details.

OEM / EIGENE MARKE

Verwandeln Sie diesen Beschaffungsleitfaden in ein Produktdossier

Teilen Sie uns Ihr Zielprodukt, die Größe, die Oberflächenausführung, die Bestellmenge und Ihre Verpackungsanforderungen mit. Ihr Team erhält vor der Angebotserstellung eine praxisorientierte Prüfung der Herstellbarkeit.

Hersteller von Badaccessoires